Fujitsu PRIMEQUEST 1000 Series Installation Manual Download Page 244

Page: 244 / 344

7.5.2

Configuring SNMP

Configure SNMP (Simple Network Management Protocol). Use Administrator privileges to configure SNMP.

Set whether to report any operational failure to an external destination, the notification destination, and other

information. You can make the following four types of setting:

Enabling SNMP

Making advanced SNMP settings

Setting SNMP trap destinations

Configuring SNMP v3

Enabling SNMP

Operations

1. Click [Network Configuration] - [Network Protocols].

The [Network Protocols] window appears. For details on the [Network Protocols] window, see 1.5.4

[Network Protocols] window in the

PRIMEQUEST 1000 Series Tool Reference

(C122-E110EN).

FIGURE 7.6 [Network Protocols] window (example)

2. Enter values for each item in [SNMP].

3. Click the [Apply] button.

Making advanced SNMP settings

Operations

1. Click [Network Configuration] - [SNMP Configuration] - [Community].

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 7 Work after Installation

216

C122-E107-09EN

Summary of Contents for PRIMEQUEST 1000 Series

























































































































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands

Fujitsu PRIMEQUEST 1000 Series, Installation Manual

Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands