Fujitsu PRIMEQUEST 1000 Series Installation Manual Download Page 245

Page: 245 / 344

The [SNMP Community] window appears. For details on the [SNMP Community] window, see [SNMP

Community] window in 1.5.6 [SNMP Configuration] menu in the

PRIMEQUEST 1000 Series Tool

Reference

(C122-E110EN).

FIGURE 7.7 [SNMP Community] window (example)

2. Enter values in the required fields.

You can set up to 16 Community lines. Enter values for the specified community, accessible IP addresses,

SNMP version, access permission, and authentication.

To delete a line, clear the [Community] and [IP address] items.

3. Click the [Apply] button.

Setting SNMP trap destinations

Operations

1. Click [Network Configuration] - [SNMP Configuration] - [Trap].

The [SNMP Trap] window appears. For details on the [SNMP Trap] window, see [SNMP Trap] window in

1.5.6 [SNMP Configuration] menu in the

PRIMEQUEST 1000 Series Tool Reference

(C122-E110EN).

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 7 Work after Installation

217

C122-E107-09EN

Summary of Contents for PRIMEQUEST 1000 Series

























































































































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Fujitsu PRIMEQUEST 1000 Series, Installation Manual, Page: 245 / 344

Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews: