manualshive.com logo in svg

Fluke OC3port Plus, User Manual

Share
Download
Fluke OC3port Plus User Manual Download Page 96

SONET/SDH Configuration and Testing

Modifying the Value of the Payload Pointer

4

4-17

Table 4-3. Description of STS-3c/STM-1 Errors (cont)

Errors

Description

Path FEBE: TX1-TX8

Pressing ENTER forces the transmitted 

PATH FEBE

 indicator

to indicate a 

Far End Block Error

. Each time ENTER is

pressed another FEBE indication is sent.

The Right or Left Arrow key can be used to change the TX1
setting to TX2…TX8. Each of these selections represents an
increase in the number of transmitted FEBE indications that
can be sent with each press of the ENTER key (for example,
selecting TX4 results in the transmission of four FEBE
indications every time you press ENTER).

Modifying the Value of the Payload Pointer

Both the SONET and SDH transmit overhead contains a payload pointer, which is
used to determine where the beginning of the 

Synchronous Payload Envelope

(SPE) is located. The starting location of the SPE within the frame may change in
order to respond to small frequency differences among various elements in a
communications network. For this reason, you may need to modify the value of
the payload pointer to determine the location of the first byte of the SPE. This
pointer can take on any value from 0 to 782 decimal. It represents the offset from
the start of the frame required to locate the SPE.

To change the value of the payload pointer, follow these steps:

1.

 

Press the 

SONET

 key. The 

SONET SELECTIONS 

menu is displayed.

2.

 

Press the 

Down Arrow

 key to move the 

Pointer Actions

 option to the selection

line:

      

SONET      SELECTIONS

             

 Setup STS-3c                          

   Pointer Actions                        

        Loopback STS-3c              OFF     

za052f.eps

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for OC3port Plus

























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands