Fluke OC3port Plus User Manual Download Page 180

Page: 180 / 248

Testing ATM Networks

Quality of Service Tests

6-49

Make sure that the

Cell Loss

option is on the selection line. Then, press

ENTER

. The

Cell Loss

submenu is displayed:

CELL LOSS:
- - - - - - - - - - - - - - - - - - - - - - - -
Start Cell Loss STD
Setup Cell Loss

za135f.eps

Press the

Down Arrow

key to move the

Setup Cell Loss

option to the selection

line. Then, press

ENTER

. The

CELL LOSS PARAMETERS

menu is displayed:

CELL LOSS PARAMETERS
- - - - - - - - - - - - - - - - - - - - - - - -
Duration: 005.0
RT Delay: 0.05

za136f.eps

10. Make sure that the

Duration

parameter

is on the selection line. This parameter

determines the amount of time for each burst of cell loss transmission. The
values of this parameter range from

0.1

300

seconds. The default value is

5.0

seconds.

11. Press the

EDIT

key to enter Edit mode and supply the desired value for the

Duration

parameter. Press

ENTER

when you are done to save the change.

12. Press the

Down Arrow

key to move the

RT Delay

option to the selection line.

This parameter sets the maximum amount of time that the OC3port Plus
should wait for the return of transmitted cells. The value of

RT Delay

ranges

from .

seconds to

9.99

seconds. The default value is

.05

seconds.

13. Press the

EDIT

key to enter Edit mode and supply the desired value for

the RT

Delay

parameter. Press

ENTER

when you are done to save the change.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for OC3port Plus

























































































































































































































































Search results

Summary of Contents for OC3port Plus

Reviews:

Brands by name

Popular brands

Fluke OC3port Plus, User Manual

Search results

Summary of Contents for OC3port Plus

Reviews:

Brands by name

Popular brands