manualshive.com logo in svg

Fluke OC3port Plus, User Manual

Share
Download
Fluke OC3port Plus User Manual Download Page 185

OC3port Plus

User Manual

6-54

Step 1: Identify the address of the trigger burst transmission and the number of

cells to send as a trigger to the slave unit.

1. Press the 

ATM

 key. The 

ATM SELECTIONS

 menu is displayed.

2.

 

Press the 

Down Arrow

 key to move the 

Setup XMIT Streams

 option to the

selection line:

ATM SELECTIONS:
Setup RX Filtrs
Setup XMIT Streams
Load XMIT Streams

za140f.eps

3. Press 

ENTER

. The setup menu for 

TRANSMIT STREAM 1

 is displayed.

4. Press the 

Right Arrow

 key to display the setup menu for 

TRANSMIT STREAM 2

.

5. Press the 

Down Arrow

 key to move the 

SOURCE

 option to the selection line.

Then, press the 

Left

 or 

Right Arrow

 key to change the setting to 

CBR

:

 TRANSMIT STREAM:           2

 

 NAME:XMITHDR_2
 SOURCE   CBR 
 VPI:0000

za141f.eps

6.

 

Press the 

Down Arrow

 key to move the 

VPI

 option to the selection line. Then,

press the 

EDIT

 key and enter a value for this option. Press 

ENTER

 to save the

change.

Continue in this manner until the entire header (

VPI, VCI, PT, CLP

, and 

GFC

options) is programmed.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for OC3port Plus

























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands