manualshive.com logo in svg

Fluke OC3port Plus, User Manual

Share
Download
Fluke OC3port Plus User Manual Download Page 23

OC3port Plus

Users Manual

1-10

Notices, Warnings, Operating Restrictions

This product complies with UL 1950 (2/26/93). This compliance has been certified
for both the United States and Canada by ETL Testing Laboratories and will carry
the ETL listing mark. This product meets the requirements of
FCC Part 15-Subpart A, electronics emission and susceptibility.

Service and adjustment of this unit is to be performed only by trained Fluke
service personnel. The following general safety precautions must be observed
during all phases of operation, service and repair of this instrument.  Failure to
comply with these precautions or with specific warnings in this book violate safety
standards of design, manufacture, and intended use of this instrument.  Fluke
Corporation assumes no liability for the customer’s failure to comply with these
requirements.

Potential Danger

•

 

Explosion Hazard: Do not operate the system in the presence of flammable
gases.

•

 

Hazardous Material: Should the LCD display become damaged, the liquid
crystal material can leak.  Avoid all contact with this material, especially
swallowing. Use soap and water to thoroughly wash all skin and clothing
contaminated with the liquid crystal material.

•

 

Electric Shock Hazard: Do not remove the system covers. To avoid electric
shock, use only the supplied power module.

•

 

Laser: This product contains a Class 1 Laser Device. Do not look into the
connector labeled "output". Invisible laser energy is emitted from that
connector whenever the laser is on.

Warning

AC adapter/charger:

 

 

Only the Fluke-supplied AC adapter/charger may be used
with this equipment. The use of any other AC
adapter/charger is expressly forbidden and will void all
warranty rights.

Outlet:

 

 

The AC socket outlet shall be installed near the equipment
and shall be easily accessible. Failure to have this outlet
easily accessible may constitute a safety hazard.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for OC3port Plus

























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands