manualshive.com logo in svg

Fluke OC3port Plus, User Manual

Share
Download
Fluke OC3port Plus User Manual Download Page 56

Setting Up and Operating the OC3port Plus

Programming the Overall Operation of the OC3port Plus

3

3-9

Caution

Be careful when you restore the factory defaults because
any settings and configurations you previously stored in
Parameter Sets will be replaced by the factory default
values.

To create a parameter set, do the following:

1.

 

Press the 

OPTIONS

 key. The 

OPTION SELECTIONS

 menu is displayed:

        

OPTION      SELECTIONS

             

     

- - - - - - - - - - - - - - - - - - - - - - -  

    Parameter Set                        1 

   RS-232   Speed                     96

za008f.eps

2.

 

Make sure that the Parameter Set option is on the selection line. Then, press
the 

Left

 or 

Right Arrow

 key to select the parameter set you want to create. For

example:

        

OPTION      SELECTIONS

             

     

- - - - - - - - - - - - - - - - - - - - - - -  

    Parameter Set                        2 

   RS-232   Speed                     96

za019f.eps

 

In this example, Parameter Set 

2

 is selected.

3.

 

Press the 

ENTER

 key. The tester resets itself and activates the parameter set

you selected. In this example, 

Parameter Set 2

 is now activated.

 

Note

 

To make sure that the parameter set you selected is the active one,
press the 

OPTIONS

 key again. The number of parameter set that is

currently active is displayed to the right of the 

Parameter Set

 option.

 

In this example, the setting for the 

Parameter Set

 option is 

2

, which indicates

that Parameter Set

 2

 is the active parameter set.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for OC3port Plus

























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands