manualshive.com logo in svg

Fluke OC3port Plus, User Manual

Share
Download
Fluke OC3port Plus User Manual Download Page 195

OC3port Plus

User Manual

6-64

Running a Remote Cell Loss Test

To run a Remote Cell Loss test, connect the two testers across the ATM network
ports under test. Then, complete the following steps first on the slave unit, then on
the master unit.

1. Press the 

ATM

 key. The 

ATM SELECTIONS

 menu is displayed.

2.

 

Press the 

Down Arrow

 key to move the 

Quality of Service

 option to the selection

line. Then, press 

ENTER

. The 

QUALITY OF SERVICE

 submenu is displayed:

  QUALITY OF SERVICE
 - - - - - - - - - - - - - - - - - - - - - - - - 
  Cell Loss
  1Pt Cel Dly Var                    1

za134f.eps

3.

 

Make sure that the 

Cell Loss

 option is on the selection line. Then, press

ENTER

. The 

CELL LOSS

 submenu is displayed:

  CELL LOSS:
 - - - - - - - - - - - - - - - - - - - - - - - -  
  Start Cell Loss   STD
  Setup Cell Loss

za135f.eps

4. Make sure that the 

Start Cell Loss

 option is on the selection line. Then, do one

of the following:

a.

If the tester you are programming is the slave unit, press the 

Left

 

or Right

Arrow

 key to change the setting to 

SLV

. Press 

ENTER

. Then, go to Step 1

and complete this entire procedure again on the master unit.

b.

 

If the tester you are programming is the master unit, press the 

Left 

or

 Right

Arrow

 key to change the setting to 

MAS

. Press 

ENTER

.

The Remote Cell Loss test begins. The master and slave units synchronize
with each other. Then, results are provided to you on the master unit’s
LCD. See "Understanding Cell Loss Test Results", which follows, for a
detailed description of the test results.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for OC3port Plus

























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands