manualshive.com logo in svg

Fluke OC3port Plus, User Manual

Share
Download
Fluke OC3port Plus User Manual Download Page 33

OC3port Plus

Users Manual

2-8

 

Table 2-2 lists the general status LEDs and their meanings.

 

Table 2-2. OC3port Plus General Status LEDs

 

LED Name

 

LED Condition

 

Meaning

 

STATUS

 

Slow blinking

 

Constant Green

 

Indicates that the laser transmitter is set to
OFF. (for single-mode units only)

 

Indicates that the laser transmitter is set to
ON. (For single-mode units only).

 

ATM CELL LOCK

 

On

 

Indicates that ATM cell delineation has been
achieved.

 

ALARMS

 

On

 

Indicates that alarms are being transmitted

 

PATTERN / ERROR
INSERT

 

On

 

Indicates that patterns or errors are being
transmitted.

 

LOOPBACK

 

On

 

Indicates that the unit is in line loopback or in
cell loopback mode.

 

POWER

 

ON

 

Blinking

 

Indicates adequate AC or battery power.

 

Indicates that the battery is low on power.

 

 

The remaining 18 LEDs, found on the right side of the tester, indicate the status of
the connected SONET network.

 

The OC3port Plus can detect nine separate alarms.

 

The red LEDs indicate active or current alarms, while the yellow (History) LEDs
indicate that an alarm occurred at some time in the past but is no longer being
detected.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for OC3port Plus

























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands