manualshive.com logo in svg

Fluke OC3port Plus, User Manual

Share
Download
Fluke OC3port Plus User Manual Download Page 77

OC3port Plus

Users Manual

3-30

Pausing a Print Job

To pause a job that is currently printing, do the following:

1.

 

From the 

PRINT SELECTIONS

 main menu, make sure that the 

Print Mode

 option

is on the selection line.

2.

 

Press the 

Right Arrow

 key to display the 

PSE

 (pause) setting.

The print job temporarily stops.

Preventing a Report from Being Printed

To prevent a report from being printed, follow these steps:

1.

 

From the 

PRINT SELECTIONS

 main menu, make sure that the 

Print Mode

 option

is on the selection line.

2.

 

Press the 

Right Arrow

 key to display the 

OFF

 setting.

All printing is currently prevented from occurring.

Controlling the OC3port Plus Remotely

For information about remote control software, contact Fluke at:

*09/)MRXLI97%ERH'EREHE

MR)YVSTI

MR.ETER

7MRKETSVI

206-356-5500 anywhere in the world

Visit Fluke’s web site at 

www.fluke.com

.

To connect the OC3port Plus to a modem, follow these steps:

1.

 

Make sure that the OC3port Plus and the modem are powered off.

2.

 

Plug one end of the RJ-11 to RJ-11 cable into the RS-232 jack, which is
located on the connector panel. Plug the other end of this cable into the RJ-11
to DB-25s adapter marked "modem/printer".

3.

 

Plug the RJ-11 to DB-25s adapter into the serial port on the modem.

4.

 

Connect the modem to the phone jack.

5.

 

Turn on the modem.

6.

 

Turn on the OC3port Plus.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for OC3port Plus

























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands