Fluke OC3port Plus User Manual Download Page 53

Page: 53 / 248

OC3port Plus

Users Manual

3-6

Press the

Down

Arrow

key to move

DATE

to the selection line. Then, press the

EDIT

key. The number in the first position of the

DATE

field flashes.

Press the

Down Arrow

key to display the desired number. Then, press the

Right Arrow

key to move to the next position and enter the desired value there.

Finally, press

ENTER

to save your selection.

Press the

Down Arrow

key to move

YEAR

to the selection line. Press the

EDIT

key to enter

Edit mode

and make the necessary changes. Make sure you press

ENTER

when you are done to save the change.

Press the

Down Arrow

key to move

TIME

to the selection line. Press the

EDIT

key to enter

Edit mode

and set the time. When you finish, press

ENTER

to save

your selection.

The tester is now configured with your date and time selections.

Setting the Communications Speed

To set the communications speed on the OC3port Plus, complete these steps:

From the

OPTION SELECTIONS

menu, press the

Down Arrow

key to move the

RS-232 Speed

option to the selection line:

OPTION SELECTIONS

Parameter Set 1

RS-232 Speed 96

Scroll Method WIN

za017f.eps

This option has these three settings:

•

9600 baud

•

2400 baud

•

1200 baud

Press the

Left

Right Arrow

key to select the correct communications speed.

The change takes effect immediately. The OC3port Plus is configured with the
baud rate you selected.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for OC3port Plus

























































































































































































































































Search results

Summary of Contents for OC3port Plus

Reviews:

Brands by name

Popular brands

Fluke OC3port Plus, User Manual

Search results

Summary of Contents for OC3port Plus

Reviews:

Brands by name

Popular brands