manualshive.com logo in svg

Fluke OC3port Plus, User Manual

Share
Download
Fluke OC3port Plus User Manual Download Page 39

OC3port Plus

Users Manual

2-14

Figure 2-5 is an illustration of the OC3port Plus menu system. All of the tester’s
functions are accessed through this menu system. On the first level is the
introductory display, which is the display you see when you first turn on or reset
the tester. On the second level are the six direct access keys. These keys control the
operation of the entire tester. When you press any one of these keys, you gain
direct access to the selected function and any of its related subfunctions.

FLUKE CORPORATION

3.3

03-14-99   7:22:10 PM

SELECT MENU FUNCTION

Press ESC twice

to reset the

SONET

SONET

SELECTIONS

ATM

SELECTIONS

BERT

SELECTIONS

AUTO

SELECTIONS

ALARM

SELECTIONS

OPTIONS

SELECTIONS

Moniter ATM
Setup RX Filtrs
Setup XMIT Streams
Load XMIT Streams
ATM XMIT Mode
Cell Capture
Quality of Service
OAM Transmit
OAM Moniter
ATM Options
Load Temp Trfc Only
Load Temp Trfc & Hdr

Laser
Moniter STS-3c
Insert Errors
Setup STS-3c
Pointer Actions
Loopback STS-3c

Start BERT
Select BERT Pat
Setup Error Inj

IP Ping
AAL Type Detect
Auto Store
ATM Activity Scan
Start Auto Test
Review Auto Test

Section LOS
Line AIS
Line FERF
Path AIS
Path FERF
Path YELLOW
LOS Action
View Alarm Log

Parameter Set
RS-232 Speed
Scroll Method
Set Buzzer
Factory Defaults
User Info
General Info
Modem Init String
Date Time Editor
Beep Alarm/Err
Auto Test Featre

ATM

BERT

AUTO

ALARMS

OPTIONS

za009f.eps

Figure 2-5. OC3port Plus Menu System (Version 3.3)

Using the Directional Arrow Keys

 

You use the directional arrow keys to scroll through OC3port Plus menus and,
where applicable, to change parameters or edit values for options. There are four
arrow keys, each named for the direction in which they point: the 

Up Arrow

 key,

the 

Down Arrow

 

key, the 

Left Arrow

 key, and the 

Right Arrow 

key.

Scrolling through Menu Options

 

The 

Up 

and 

Down Arrow

 keys are used to scroll through the options listed on

OC3port Plus menus.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for OC3port Plus

























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands