manualshive.com logo in svg

Fluke OC3port Plus, User Manual

Share
Download
Fluke OC3port Plus User Manual Download Page 189

OC3port Plus

User Manual

6-58

4.

 

Press the 

Down Arrow

 key to move the 

Setup Cell Loss

 option to the selection

line. Then, press 

ENTER

. The 

CELL LOSS PARAMETERS

 submenu is

displayed:

  CELL LOSS PARAMETERS
 - - - - - - - - - - - - - - - - - - - - - - - -  
  Duration:  005.0
  RT Delay:  0.05

za136f.eps

5. Make sure that the 

Duration

 parameter is on the selection line. This parameter

determines how long the slave unit transmits the burst of cells to the master
unit. The default setting is 

005.0

 seconds.

Press the 

EDIT

 key and enter a value for the Duration parameter. Press 

ENTER

when you finish to save the change.

6. Press the 

Down Arrow

 key to move the 

RT Delay

 parameter to the selection line.

This parameter determines the amount of time the master unit waits to receive
cells back from the slave unit.

Notes

The amount of time the master unit waits begins when it sends the
initial trigger to the slave unit and ends when it receives the cells
sent from the slave unit.

When setting the 

RT Delay

 value, you need to take into consideration

the time for the initial transmission (the trigger), the slave unit’s
receipt of the trigger, and the slave unit’s transmission of cells back
to the master unit. Because of inherent delays in this process, you
will probably have to increase (as compared with a regular Cell Loss
test) the value of the 

RT Delay

 parameter.

7. Press the 

EDIT

 key and enter a value for the 

RT Delay

 parameter. Press 

ENTER

when you finish to save the change.

You have completed the configuration of the master unit for the 

Remote Cell

Loss 

test.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for OC3port Plus

























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands