manualshive.com logo in svg

Fluke OC3port Plus, User Manual

Share
Download
Fluke OC3port Plus User Manual Download Page 28

Getting Started

Introduction

2

2-3

Introduction

 

Chapter 2 first acquaints you with the physical layout of the OC3port Plus so that
you know where the various controls and connections are located and understand
the functions of the keys and general status indicators. Next, it describes the menu
interface and shows you how to access the menus and navigate through them.
Finally, chapter 2 describes how to connect the OC3port Plus to an external power
source and how to connect the tester to the network and to remote devices.

OC3port Plus Controls and Connections

 

The OC3port Plus has two main panels: a connector panel and a front panel with
status and control sections. Take a moment to become familiar with these two
panels so that you can work more efficiently.

The Connector Panel

Figure 2-1 is a representation of the OC3port Plus connector panel.

OUT

IN

Single mode displayed

5VDC

RS232

za002f.eps

Figure 2-1. OC3port Plus Connector Panel

The connector panel, which is located on the top of the tester, has a 

5V DC

 input

jack.

Use this jack to attach the AC adapter/charger supplied by Fluke Corporation.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for OC3port Plus

























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands