Docomo F-08A, Manual

Page: 380 / 462

378
Appendix/Troubleshooting
● Dial callout restricted.
This prohibited operation is unavailable in Keypad
dial lock ON.
→ P103
● Error in IC card data. Unable to delete software.
Osaifu-Keitai compatible i-
α
ppli containing errors in
the IC card data cannot be deleted.
● Error in image. Does not work correctly.
Unable to display the Flash graphics due to image
error.
●
Error in storage area. Unable to use password
manager. Quitting.
Password save/quote is disabled due to an error in
Password manager memory space.
● Failed to activate.
Activate 1Seg could not be activated due to an error
in activation or station selection process.
● Failed to read/clear call cost information.
UIM is not correctly installed or the card is faulty. →
P40
●
i-
α
ppli stand-by display terminated due to security
error.
The i-
α
ppli stand-by display has been closed due to
an unpermitted operation or i-
α
ppli action.
● Infrared/iC transmission Connection interrupted.
An error occurred during communication or
transmission. Do not move FOMA terminal from the
right location before data sending/receiving
completes.
→ P281
● Infrared/iC transmission Failed to connect via
authentication.
Sending or receiving all data was failed because the
authentication password is not correct.
→ P282, 283
● Infrared/iC transmission No response. Retry data
exchange?
A certain period of time elapsed since
communication starts, but no communicating parties
are found. Locate your and the other party's FOMA
terminals or Bluetooth devices correctly.
→ P281
● Infrared/iC transmission No UIM, requested
software failed to start.
Even if an i-
α
ppli To is set to data received, it is not
activated due to UIM operation restriction. → P40
●
Input error (205)
Input data for the site or website is incorrect.
● Insert UIM.
UIM may not be correctly installed or the card may
not be damaged.
→ P40
●
Insufficient memory.
Operation interrupted due to insufficient memory. If
it appears frequently, once turn OFF FOMA terminal
and then turn it ON.
● Invalid data. Connection cannot be established.
(400)
Cannot be connected because of the error in the site
or website. Make sure the URL.
● Invalid data. Unable to save.
Data received through infrared communications/iC
transmission cannot be saved because it is in a
format incompatible with FOMA terminal.
● Invalid data.(xxx)
･
The specified site or website does not support i-
mode.
･
Unable to display because there is an error in the
received data.
･ Sending auto-send message failed.
● Invalid microSD. Unable to use DRM function.
Accessing the authentication area in microSD card is
disabled for a certain reason. Data compatible with
data transfer cannot be saved to microSD card with
errors.
● Invalid UIM. Requested service not available.
Operation is disabled by UIM operation restriction. →
P40
● Invalid UIM, requested software failed to start.
i-
α
ppli cannot start by UIM operation restriction. →
P40
● Is the ToruCa automatic reading function in a
mobile phone used through the reader/writer?
Select "Yes" and set ToruCa auto-read to "ON".
● 以下の宛先にはメール送信できませんでした（
561
）
Mails could not be sent to following address.(561) ○
○ @ △△△ .ne.jp
Sending i-mode mail to the following address failed :
Press
g
to display the receiver address of the failed
message sending. Check the receiver address and
retry sending in a place with good radio wave
conditions. Mail addresses displayed in the message
vary by the destinations.
● Message kept in center.
SMS have already been sent.
●
No content is available.(204)
Could not find data at the specified site.
●
No response.(408)
Unable to receive a response from a site or website
within the specified time and the communication is
disconnected. Retry later.
● Omakase Lock activated.
Omakase Lock is ON.
→
P101
● Out of 1Seg service area.
･ Reception fails because you are out of
broadcasting service area. Retry the operation in a
place with good radio wave conditions.
･
Reception fails because the channel is chargeable
or for a certain reason.
● Out of service area.
Unable to perform because the terminal is in a place
where radio waves do not reach or out of the service
area.
● Page is not found.(404)
Make sure the URL is correct.