Docomo F-08A, Manual, Page: 190 / 462

188
Camera
✔
INFORMATION
･
When shooting with in-camera, "Auto" cannot be set.
･
When Continuous (Auto) or 4 frames (Auto) is set for still image shooting, "Night scene"
cannot be set.
･
Only images of Stand-by/WVGA (480
×
854) or smaller can be set to "Monochrome
sketch" or "Colored sketch" for still image shooting.
･
For still image shooting, "Monochrome sketch", "Colored sketch", "Skin tone enhance",
"Eye enhance-Lo/-Hi" and "Eye+Skin enhance-Lo/-Hi" cannot be set with Continuous/4
frames/Panorama shooting.
･
When setting to other than "Auto" or "Standard", white balance settings cannot be
changed. And, the settings of Brightness are retained until switched to "Auto" or
"Standard".
･
Effects of "Skin tone enhance", "Eye enhance-Lo/-Hi" and "Eye+Skin enhance-Lo/-Hi"
may not work in the following cases or other shooting conditions.
- A face is turned away or tilted
- A face is partially covered with eye glasses, a hat, mask or shadow
- A face is extremely small, large or dark against the entire screen
- A face is at the edge of the screen
◆
Adjusting brightness
1
On the shooting screen,
m21 e 1
-
5
◆
Adjusting white balance
･
You can adjust it when Scene mode/effect is set to "Auto" or "Standard".
1
On the shooting screen,
m22 e 1
-
5
◆
Adjusting flicker
Adjusting flicker can suppress the flicker phenomena which cause flickering or
fringe patterns on the screen under light such as fluorescent lights.
1
On the shooting screen,
m23 e 1
-
3
Auto : Adjust automatically to eliminate flickering.
50 Hz (East-Japan) : Adjust to match the power frequency in eastern Japan.
60 Hz (West-Japan) : Adjust to match the power frequency in western Japan.
･
If flickering still remains in "Auto", set according to the area you stay.
･
This setting is retained even when Camera is ended. This setting also applies
to the flicker adjustment of Videophone and Bar code reader.
✔
INFORMATION
･
The flicker may not disappear in a very bright place such as under fluorescent lights.
･
When the shake reduce function is used with Adjust flicker set to "Auto", Adjust flicker
may not function satisfactorily. In this case, it is recommended to set Adjust flicker
according to the area you stay.
◆ Restoring default settings for Brightness
･
The settings of Scene mode/effect, Brightness, White balance and Adjust flicker
are reset to the default settings.
1
On the shooting screen,
m24 e
"Yes"
◆ Switching Reduce shake ON/OFF
1
On the still image shooting screen,
m41
or on the moving
picture shooting screen,
m4
✔
INFORMATION
･
The setting is "OFF" in the following cases.
- During Continuous/4 frames/Panorama
- Shooting with in-camera
- When Still camera is activated from i-
α
ppli or while i-
α
ppli is running
･
The effect of auto correction is not achieved for some subject or shooting condition.
◆ Correcting skew
For shooting a still image, correct skew of images to make characters more easy to
read.
1
On the still image shooting screen,
m42 e 1
-
3
✔
INFORMATION
･
This function cannot be used with the following functions or settings.
- During Continuous/4 frames/Panorama
- Shooting with in-camera
- When Still camera is activated from i-
α
ppli or while i-
α
ppli is running
- When Scene mode/effect is "Skin tone enhance", "Eye enhance-Lo/-Hi" or "Eye+Skin enhance-Lo/
-Hi"
- When Image size is QVGA (240
×
320, 320
×
240) or smaller