Dell S4820T, Configuration Manual

Page: 129 / 1178

| | OUT-L2 ACL | 0 | 0 | 0
11 | 1 | IN-L2 ACL | 7152 | 0 | 7152
| | IN-L2 FIB | 32768 | 1081 | 31687
| | OUT-L2 ACL | 0 | 0 | 0
The following output displays CAM space usage for Layer 3 ACLs:
Dell#show cam-usage router
Linecard|Portpipe| CAM Partition | Total CAM | Used CAM |Available CAM
========|========|=================|=============|=============|==============
11 | 0 | IN-L3 ACL | 8192 | 3 | 8189
| | IN-L3 FIB | 196607 | 1 | 196606
| | IN-L3-SysFlow | 2878 | 0 | 2878
| | IN-L3-TrcList | 1024 | 0 | 1024
| | IN-L3-McastFib | 9215 | 0 | 9215
| | IN-L3-Qos | 8192 | 0 | 8192
| | IN-L3-PBR | 1024 | 0 | 1024
| | OUT-L3 ACL | 16384 | 0 | 16384
11 | 1 | IN-L3 ACL | 8192 | 3 | 8189
| | IN-L3 FIB | 196607 | 1 | 196606
| | IN-L3-SysFlow | 2878 | 0 | 2878
| | IN-L3-TrcList | 1024 | 0 | 1024
| | IN-L3-McastFib | 9215 | 0 | 9215
| | IN-L3-Qos | 8192 | 0 | 8192
| | IN-L3-PBR | 1024 | 0 | 1024
| | OUT-L3 ACL | 16384 | 0 | 16384
Allocating FP Blocks for VLAN Processes
The VLAN contentaware processor (VCAP) application is a pre-ingress CAP that modifies the VLAN
settings before packets are forwarded. To support ACL CAM optimization, the CAM carving feature is
enhanced. A total of four VCAP groups are present: two fixed groups and two dynamic groups. Of the
two dynamic groups, you can allocate zero, one, or two FP blocks to iSCSI Counters, Open Flow, and
ACL Optimization.
You can configure only two of these features at a time.
• To allocate the number of FP blocks for VLAN open flow operations, use the
cam-acl-vlan
vlanopenflow <0-2>
command.
• To allocate the number of FP blocks for VLAN iSCSI counters, use the
cam-acl-vlan vlaniscsi
<0-2>
command.
• To allocate the number of FP blocks for ACL VLAN optimization, use the
cam-acl-vlan
vlanaclopt <0-2>
command.
To reset the number of FP blocks to the default, use the
no
version of these commands. By default, zero
groups are allocated for the ACL in VCAP. ACL VLAN groups or CAM optimization is not enabled by
default. You must also allocate the slices for CAM optimization.
To display the number of FP blocks that is allocated for the different VLAN services, use the
show cam-
acl-vlan
command. After you configure the ACL VLAN groups, reboot the system to store the settings
in nonvolatile storage. During CAM initialization, the chassis manager reads the NVRAM and allocates the
dynamic VCAP regions.
Access Control List (ACL) VLAN Groups and Content Addressable Memory (CAM)
129