debug ip bgp [
ip-address
| peer-group
peer-group-name
] notifications [in |
out]
• View information about BGP updates and filter by prefix name.
EXEC Privilege mode
debug ip bgp [
ip-address
| peer-group
peer-group-name
] updates [in | out]
[prefix-list name]
• Enable soft-reconfiguration debug.
EXEC Privilege mode
debug ip bgp {
ip-address
|
peer-group-name
} soft-reconfiguration
To enhance debugging of soft reconfig, use the
bgp soft-reconfig-backup
command only when
route-refresh is not negotiated to avoid the peer from resending messages.
In-BGP is shown using the
show ip protocols
command.
Dell Networking OS displays debug messages on the console. To view which debugging commands are
enabled, use the
show debugging
command in EXEC Privilege mode.
To disable a specific
debug
command, use the keyword
no
then the
debug
command. For example, to
disable debugging of BGP updates, use
no debug ip bgp updates
command.
To disable all BGP debugging, use the
no debug ip bgp
command.
To disable all debugging, use the
undebug all
command.
Storing Last and Bad PDUs
Dell Networking OS stores the last notification sent/received and the last bad protocol data unit (PDU)
received on a per peer basis. The last bad PDU is the one that causes a notification to be issued.
In the following example, the last seven lines shown in bold are the last PDUs.
Example of the
show ip bgp neighbor
Command to View Last and Bad PDUs
Dell(conf-router_bgp)#do show ip bgp neighbors 1.1.1.2
BGP neighbor is 1.1.1.2, remote AS 2, external link
BGP version 4, remote router ID 2.4.0.1
BGP state ESTABLISHED, in this state for 00:00:01
Last read 00:00:00, last write 00:00:01
Hold time is 90, keepalive interval is 30 seconds
Received 1404 messages, 0 in queue
3 opens, 1 notifications, 1394 updates
6 keepalives, 0 route refresh requests
Sent 48 messages, 0 in queue
3 opens, 2 notifications, 0 updates
43 keepalives, 0 route refresh requests
Minimum time between advertisement runs is 30 seconds
Minimum time before advertisements start is 0 seconds
Capabilities received from neighbor for IPv4 Unicast :
MULTIPROTO_EXT(1)
ROUTE_REFRESH(2)
CISCO_ROUTE_REFRESH(128)
254
Border Gateway Protocol IPv4 (BGPv4)
Summary of Contents for S4820T
