To verify the VRRP group priority, use the
show vrrp
command.
Dellshow vrrp
------------------
TenGigabitEthernet 1/1, VRID: 111, Net: 10.10.10.1
State: Master, Priority: 255, Master: 10.10.10.1 (local)
Hold Down: 0 sec, Preempt: TRUE, AdvInt: 1 sec
Adv rcvd: 0, Bad pkts rcvd: 0, Adv sent: 2343, Gratuitous ARP sent: 5
Virtual MAC address:
00:00:5e:00:01:6f
Virtual IP address:
10.10.10.1 10.10.10.2 10.10.10.3 10.10.10.10
Authentication: (none)
------------------
TenGigabitEthernet 1/2, VRID: 111, Net: 10.10.2.1
State: Master, Priority: 125, Master: 10.10.2.1 (local)
Hold Down: 0 sec, Preempt: TRUE, AdvInt: 1 sec
Adv rcvd: 0, Bad pkts rcvd: 0, Adv sent: 601, Gratuitous ARP sent: 2
Virtual MAC address:
00:00:5e:00:01:6f
Virtual IP address:
10.10.2.2 10.10.2.3
Authentication: (none)
Configuring VRRP Authentication
Simple authentication of VRRP packets ensures that only trusted routers participate in VRRP processes.
When you enable authentication, Dell Networking OS includes the password in its VRRP transmission.
The receiving router uses that password to verify the transmission.\
NOTE: You must configure all virtual routers in the VRRP group the same: you must enable
authentication with the same password or authentication is disabled.
To configure simple authentication, use the following command.
• Configure a simple text password.
INTERFACE-VRID mode
authentication-type simple [
encryption-type
]
password
Parameters:
–
encryption-type
:
0
indicates unencrypted;
7
indicates encrypted.
–
password
: plain text.
Examples of the
authentication-type
Command
The bold section shows the encryption type (encrypted) and the password.
Dell(conf-if-te-1/1-vrid-111)#authentication-type ?
Dell(conf-if-te-1/1-vrid-111)#authentication-type
simple 7 force10
The following example shows verifying the VRRP authentication configuration using the
show conf
command. The bold section shows the encrypted password.
Dell(conf-if-te-1/1-vrid-111)#show conf
!
vrrp-group 111
authentication-type simple 7
387a7f2df5969da4
priority 255
virtual-address 10.10.10.1
Virtual Router Redundancy Protocol (VRRP)
1123
Summary of Contents for S4820T
