BigIron RX Series Configuration Guide
1295
53-1001810-01
Syslog messages
A
Notification
VRRP intf state changed,
intf
<portnum>
, vrid
<virtual-router-id>
,
state
<vrrp-state>
A state change has occurred in a Virtual
Router Redundancy Protocol (VRRP)
interface.
The
<portnum>
is the port.
The
<virtual-router-id>
is the virtual router ID
(VRID) configured on the interface.
The
<vrrp-state>
can be one of the following:
•
init
•
master
•
backup
•
unknown
Notification
BGP Peer
<ip-addr>
UP (ESTABLISHED)
Indicates that a BGP4 neighbor has come up.
The
<ip-addr>
is the IP address of the
neighbor’s BGP4 interface with the BigIron
RX.
Notification
BGP Peer
<ip-addr>
DOWN (IDLE)
Indicates that a BGP4 neighbor has gone
down.
The
<ip-addr>
is the IP address of the
neighbor’s BGP4 interface with the BigIron
RX.
Notification
Local ICMP exceeds
<burst-max>
burst
packets, stopping for
<lockup>
seconds!!
The number of ICMP packets exceeds the
<burst-max>
threshold set by the ip icmp
burst command. The BigIron RX may be the
victim of a Denial of Service (DoS) attack.
All ICMP packets will be dropped for the
number of seconds specified by the
<lockup>
value. When the lockup period expires, the
packet counter is reset and measurement is
restarted.
Notification
Local TCP exceeds
<burst-max>
burst
packets, stopping for
<lockup>
seconds!!
The number of TCP SYN packets exceeds the
<burst-max>
threshold set by the ip tcp burst
command. The BigIron RX may be the victim
of a TCP SYN DoS attack.
All TCP SYN packets will be dropped for the
number of seconds specified by the
<lockup>
value. When the lockup period expires, the
packet counter is reset and measurement is
restarted.
Notification
Transit ICMP in interface
<portnum>
exceeds
<num>
burst packets, stopping for
<num>
seconds!!
Threshold parameters for ICMP transit
(through) traffic have been configured on an
interface, and the maximum burst size for
ICMP packets on the interface has been
exceeded.
The
<portnum>
is the port number.
The first
<num>
is the maximum burst size
(maximum number of packets allowed).
The second
<num>
is the number of seconds
during which additional ICMP packets will be
blocked on the interface.
Note: This message can occur in response to
an attempted Smurf attack.
TABLE 222
Brocade Syslog messages (Continued)
Message level
Message
Explanation
Summary of Contents for Brocade DCX
