BigIron RX Series Configuration Guide
1191
53-1001810-01
Configuring an IPv6 ACL
47
TABLE 203
Syntax descriptions
Arguments...
Description...
ipv6 access-list
<acl name>
Enables the IPv6 configuration level and defines the name of the IPv6 ACL.
The
<acl name>
can contain up to 199 characters and numbers, but cannot
begin with a number and cannot contain any spaces or quotation marks.
permit
The ACL will permit (forward) packets that match a policy in the access list.
deny
The ACL will deny (drop) packets that match a policy in the access list.
icmp
Indicates the you are filtering ICMP packets.
protocol
The type of IPv6 packet you are filtering. You can specify a well-known name
for some protocols whose number is less than 255. For other protocols, you
must enter the number. Enter “?” instead of a protocol to list the well-known
names recognized by the CLI. IPv6 protocols include:
•
AHP – Authentication Header
•
ESP – Encapsulating Security Payload
•
IPv6 – Internet Protocol version 6
•
SCTP – Stream Control Transmission Protocol
<ipv6-source-prefix>/<prefix-leng
th>
The
<ipv6-source-prefix>/<prefix-length>
parameter specify a source prefix
and prefix length that a packet must match for the specified action (deny or
permit) to occur. You must specify the
<ipv6-source-prefix>
parameter in
hexadecimal using 16-bit values between colons as documented in RFC 2373.
You must specify the
<prefix-length>
parameter as a decimal value. A slash
mark (/) must follow the
<ipv6-prefix>
parameter and precede the
<prefix-length>
parameter.
<ipv6-destination-prefix>/<prefix
-length>
The
<ipv6-destination-prefix>/<prefix-length>
parameter specify a
destination prefix and prefix length that a packet must match for the specified
action (deny or permit) to occur. You must specify the
<ipv6-destination-prefix>
parameter in hexadecimal using 16-bit values
between colons as documented in RFC 2373. You must specify the
<prefix-length>
parameter as a decimal value. A slash mark (/) must follow
the
<ipv6-prefix>
parameter and precede the
<prefix-length>
parameter
any
When specified instead of the
<ipv6-source-prefix>/<prefix-length>
or
<ipv6-destination-prefix>/<prefix-length>
parameters, matches any IPv6
prefix and is equivalent to the IPv6 prefix::/0.
host
Allows you specify a host IPv6 address. When you use this parameter, you do
not need to specify the prefix length. A prefix length of all128 is implied.
icmp-type
ICMP packets can be filtered by ICMP message type. The type is a number
from 0 to 255.
icmp code
ICMP packets, which are filtered by ICMP message type can also be filtered by
the ICMP message code. The code is a number from 0 to 255,
icmp-message
ICMP packets,are filtered by ICMP messages. Refer to
“ICMP message
configurations”
on page 1194 for a list of ICMP message types.
tcp
Indicates the you are filtering TCP packets.
udp
Indicates the you are filtering UDP packets.
Summary of Contents for Brocade DCX
