118
BigIron RX Series Configuration Guide
53-1001810-01
Configuring an interface as the source for all Telnet packets
5
NOTE
Messages for accessing the User EXEC level apply only to access through Telnet. The device does
not authenticate initial access through serial connections but does authenticate serial access to the
Privileged EXEC level. Messages for accessing the Privileged EXEC level apply to access through the
serial connection or Telnet.
The following examples show login and logout messages for the User EXEC and Privileged EXEC
levels of the CLI.
Syntax: show logging
The first message (the one on the bottom) indicates that user “dg” logged in to the CLI’s User EXEC
level on October 15 at 5:38 PM and 3 seconds (Oct 15 17:38:03). The same user logged into the
Privileged EXEC level four seconds later.
The user remained in the Privileged EXEC mode until 5:59 PM and 22 seconds. (The user could
have used the CONFIG modes as well. Once you access the Privileged EXEC level, no further
authentication is required to access the CONFIG levels.) At 6:01 PM and 11 seconds, the user
ended the CLI session.
Disabling the Syslog messages and traps
Logging of CLI access is enabled by default. To disable logging of CLI access, enter the following
commands.
BigIron RX
(config)# no logging enable user-login
BigIron RX
(config)# write memory
BigIron RX
(config)# end
BigIron RX
# reload
Syntax: [no] logging enable user-login
Refer to the MIB Guide for a list of traps.
Configuring an interface as the source for all Telnet packets
You can designate the lowest-numbered IP address configured an interface as the source IP
address for all Telnet packets from the device. Identifying a single source IP address for Telnet
packets provides the following benefits:
•
If your Telnet server is configured to accept packets only from specific links or IP addresses,
you can simplify configuration of the Telnet server by configuring the device to always send the
Telnet packets from the same link or source address.
BigIron RX
(config)# show logging
Syslog logging: enabled (0 messages dropped, 0 flushes, 0 overruns)
Buffer logging: level ACDMEINW, 12 messages logged
level code: A=alert C=critical D=debugging M=emergency E=error
I=informational N=notification W=warning
Static Log Buffer:
Dec 15 19:04:14:A:Fan 1, fan on right connector, failed
Dynamic Log Buffer (50 entries):
Oct 15 18:01:11:info:dg logout from USER EXEC mode
Oct 15 17:59:22:info:dg logout from PRIVILEGE EXEC mode
Oct 15 17:38:07:info:dg login to PRIVILEGE EXEC mode
Oct 15 17:38:03:info:dg login to USER EXEC mode
Summary of Contents for Brocade DCX
