Chrysler pacifica hybrid 2017 Owner'S Manual Download Page 430 | Manualshive

Page: 430 / 604

background image

Jump-Starting Procedure

WARNING!

Failure to follow this jump starting procedure could
result in personal injury or property damage due to
battery explosion.

CAUTION!

Failure to follow these procedures could result in
damage to the charging system of the booster vehicle
or the discharged vehicle.

Connecting The Jumper Cables

1. Connect the positive

(+)

end of the jumper cable to the

positive

(+)

post of the vehicle with the discharged

battery.

2. Connect the opposite end of the positive

(+)

jumper

cable to the positive

(+)

post of the booster battery.

3. Connect the negative

(-)

end of the jumper cable to the

negative

(-)

post of the booster battery.

4. Connect the opposite end of the negative

(-)

jumper

cable to the negative post near the windshield cowl
(exposed metal post of the discharged vehicle).

WARNING!

Do not connect the jumper cable to the negative (-) post
of the discharged battery. The resulting electrical spark
could cause the battery to explode and could result in
personal injury. Only use the specific ground point, do
not use any other exposed metal parts.

5. Start the vehicle that has the booster battery, let the

vehicle run a few minutes, and then cycle the ignition to
ON/RUN in the vehicle with the discharged battery.

6. Once the ignition is cycled to ON/RUN, select the gear

that is needed for moving the vehicle. In most instances
of an emergency, this would be neutral. Once the proper
gear is selected, remove the jumper cables in the reverse
sequence:

Disconnecting The Jumper Cables

1. Disconnect the negative

(-)

end of the jumper cable from

the ground of the vehicle with the discharged battery.

428

IN CASE OF EMERGENCY

«
...
428
429
430
431
432
...
»

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for pacifica hybrid 2017

Brand: Accel Pages: 2

Brand: Falcon Pages: 8

Brand: Warrior Products Pages: 2

Brand: AccuAir Pages: 40

Brand: Peak Pages: 10

Brand: Porsche Pages: 195

CARPOWER CAP-12XHQ

Brand: Monacor Pages: 5

Grand Cherokee WK2

Brand: Jeep Pages: 338

Xplore Pro II SxS

Brand: Marlon Pages: 15

Brand: Inbay Pages: 20

Brand: Nav TV Pages: 4

Brand: Unex Pages: 30

Brand: Billien Pages: 2

Brand: Lexus Pages: 28

Brand: Acura Pages: 7

Brand: SAFARI Pages: 5

Brand: Peiying Pages: 32

Brand: Phonocar Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands