manualshive.com logo in svg

Chrysler pacifica hybrid 2017, Owner'S Manual

The 2017 Chrysler Pacifica Hybrid comes with an informative Owner's Manual that provides detailed instructions and guidelines for maximizing the potential of your vehicle. You can easily download this manual for free from our website, ensuring that you have access to all the information you need to enjoy your Pacifica Hybrid to the fullest.

Share
Download
background image

If the sealant (white fluid) does not flow within 0 – 10
seconds through the Sealant Hose:

1. Push the Power Button to turn Off the Tire Service Kit.

Disconnect the Sealant Hose from the valve stem. Make
sure the valve stem is free of debris. Reconnect the
Sealant Hose to the valve stem. Check that the Mode
Select Knob is in the Sealant Mode position and not Air
Mode. Push the Power Button to turn On the Tire
Service Kit.

2. Connect the Power Plug to a different 12 Volt power

outlet in your vehicle or another vehicle, if available.
Make sure the vehicle is running before turning ON the
Tire Service Kit.

3. The Sealant Bottle may be empty due to previous use.

Call for assistance.

If the sealant (white fluid) does flow through the Sealant
Hose:

1. Continue to operate the pump until

sealant is no longer flowing through
hose (typically takes 30 - 70 seconds).
As the sealant flows through the Seal-
ant Hose, the Pressure Gauge can
read as high as 70 psi (4.8 Bar). The
Pressure Gauge will decrease quickly
from approximately 70 psi (4.8 Bar) to
the actual tire pressure when the Seal-
ant Bottle is empty.

2. The pump will start to inject air into

the tire immediately after the Sealant
Bottle is empty. Continue to operate
the pump and inflate the tire to the
cold tire inflation pressure found on
the tire and loading information label
located in the driver-side door open-
ing. Check the tire pressure by look-
ing at the Pressure Gauge.

420

IN CASE OF EMERGENCY

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for pacifica hybrid 2017

Parrot CK3300 Setup Information Manual preview
CK3300
Brand: Parrot Pages: 19
Parrot Minikit+ Quick Start Manual preview
Minikit+
Brand: Parrot Pages: 88
Parrot Minikit+ Information Sheet preview
Minikit+
Brand: Parrot Pages: 2
Parrot CK3100 LCD Specifications preview
CK3100 LCD
Brand: Parrot Pages: 2
Parrot CK 3000 Evolution Installation Notes preview
CK 3000 Evolution
Brand: Parrot Pages: 8
Parrot CK 3000 Evolution User Manual preview
CK 3000 Evolution
Brand: Parrot Pages: 106
Saab 92X Owner'S Manual preview
92X
Brand: Saab Pages: 445
Wagan Wireless Handsfree Car Kit User Manual preview
Wireless Handsfree Car Kit
Brand: Wagan Pages: 20
Scosche BTFREQ PRO BTFMPD3SR Manual preview
BTFREQ PRO BTFMPD3SR
Brand: Scosche Pages: 16
Hyundai Santa Fe 2006 Owner'S Manual preview
Santa Fe 2006
Brand: Hyundai Pages: 280
Lit Lightz RGBW Rock Lights Setup Manual preview
RGBW Rock Lights
Brand: Lit Lightz Pages: 3
Jeep Cherokee 1977 Owner'S Manual preview
Cherokee 1977
Brand: Jeep Pages: 136
Black Horse Off Road TO20 Installation Instructions Manual preview
TO20
Brand: Black Horse Off Road Pages: 7
Xpresskit DBALL2-HK7 Installation Manual preview
DBALL2-HK7
Brand: Xpresskit Pages: 18
Thule 1061-1-011 Fitting Instructions preview
1061-1-011
Brand: Thule Pages: 3
Fleetwood Bounder turbo diesel 2001 Instructions Manual preview
Bounder turbo diesel 2001
Brand: Fleetwood Pages: 166
Audiovox Electronics HR7012M Installation Manual preview
HR7012M
Brand: Audiovox Electronics Pages: 12
Quadratec QRC Installation Manual preview
QRC
Brand: Quadratec Pages: 8

Brands by name

Popular brands

Load more brands