Chrysler pacifica hybrid 2017 Owner'S Manual Download Page 72 | Manualshive

Page: 72 / 604

background image

Manual Adjustment (Rear Seats)

WARNING!

•

Adjusting a seat while the vehicle is moving is
dangerous. The sudden movement of the seat could
cause you to lose control. The seat belt might not be
adjusted properly and you could be injured. Adjust
the seat only while the vehicle is parked.

•

Do not ride with the seatback reclined so that the
shoulder belt is no longer resting against your chest.
In a collision you could slide under the seat belt and
be seriously or even fatally injured. Use the recliner
only when the vehicle is parked.

Manual Rear Seat Adjuster

Both second row seats are adjustable forward or rearward.
The manual seat adjustment handle is located under the
seat cushion at the front edge of each seat.

While sitting in the seat, pull up on the handle and slide the
seat forward or rearward. Release the bar once you have
reached the desired position. Then, using body pressure,
move forward and rearward on the seat to be sure that the
seat adjusters have latched.

WARNING!

•

Adjusting a seat while driving may be dangerous.
Moving a seat while driving could result in loss of
control which could cause a collision and serious
injury or death.

(Continued)

Manual Seat Adjuster

70

GETTING TO KNOW YOUR VEHICLE

«
...
70
71
72
73
74
...
»

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for pacifica hybrid 2017

Brand: iDataLink Pages: 9

Brand: Triumph Pages: 86

BLACK STEEL S2560

Brand: Fab Fours Pages: 9

CARPOWER CAP-12XHQ

Brand: Monacor Pages: 5

Grand Cherokee WK2

Brand: Jeep Pages: 338

Brand: Pacbrake Pages: 14

2008 MX-5 Miata

Brand: Mazda Pages: 400

Brand: Hama Pages: 75

signal mirror 2005-2009 Ford Mustang

Brand: muth Pages: 9

Brand: B-Speech Pages: 4

Brand: Radical Sportscars Pages: 44

Brand: Saab Pages: 15

Brand: Autoplugin Pages: 8

Brand: Velleman Pages: 17

Brand: Westin Pages: 2

Brand: Chevrolet Pages: 55

Brand: Directed Pages: 24

Brand: Yakima Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands