Chrysler pacifica hybrid 2017 Owner'S Manual Download Page 300 | Manualshive

Page: 300 / 604

background image

In the event of a momentary problem, the transmission can
be reset to regain all forward gears by performing the
following steps:

1. Stop the vehicle.

2. Shift the transmission into PARK, if possible. If not, shift

the transmission to NEUTRAL.

3. Push and hold the ignition switch until the vehicle turns

OFF.

4. Wait approximately 30 seconds.

5. Restart the vehicle.

6. Shift into the desired gear range. If the problem is no

longer detected, the transmission will return to normal
operation.

NOTE:

Even if the transmission can be reset, we recom-

mend that you visit your authorized dealer at your earliest
possible convenience. Your authorized dealer has diagnos-
tic equipment to determine if the problem could recur. If
the transmission cannot be reset, authorized dealer service
is required.

ACTIVE NOISE CANCELLATION

Your vehicle is equipped with an Active Noise Cancellation
System. This system is designed to address exhaust and
engine noise. The system relies on four microphones
embedded in the headliner, which monitor exhaust and
engine noise, and assists an onboard frequency generator,
which creates counteracting sound waves in the audio
system’s speakers. This helps keep the vehicle quiet at idle
and during drive.

POWER STEERING

The electric power steering system will give you good
vehicle response and increased ease of maneuverability in
tight spaces. The system will vary its assist to provide light
efforts while parking and good feel while driving. If the
electric steering system experiences a fault that reduces
assist or prevents the vehicle from providing assist, you
will still have the ability to steer the vehicle manually.

298

STARTING AND OPERATING

«
...
298
299
300
301
302
...
»

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for pacifica hybrid 2017

Brand: Vauxhall Pages: 177

Brand: NavLinkz Pages: 4

Porsche 911 GT3 R

Brand: iRacing Pages: 25

Brand: Condor Pages: 2

Brand: Mercedes-Benz Pages: 368

Brand: Subaru Pages: 16

Brand: Yakima Pages: 12

Brand: Axxess Pages: 16

Brand: CrimeStopper Pages: 1

Brand: DriveRight Pages: 16

Brand: NavInc Pages: 6

Denali 1094-0185-15

Brand: E&G Classics Pages: 3

Brand: Metra Electronics Pages: 2

Brand: Lantronix Pages: 51

Brand: POOL-LINE Pages: 2

Even Brake 9400

Brand: Roadmaster Pages: 20

Brand: ideus Pages: 116

Brand: Yakima Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands