manualshive.com logo in svg

Chrysler pacifica hybrid 2017, Owner'S Manual

The 2017 Chrysler Pacifica Hybrid comes with an informative Owner's Manual that provides detailed instructions and guidelines for maximizing the potential of your vehicle. You can easily download this manual for free from our website, ensuring that you have access to all the information you need to enjoy your Pacifica Hybrid to the fullest.

Share
Download
background image

If the tire pressure is 19 psi (1.3 Bar) or higher:

1. Push the Power Button to turn on

Tire Service Kit and inflate the tire to
the cold tire inflation pressure found
on the tire and loading information
label located in the driver-side door
opening.

NOTE:

If the tire becomes over-inflated, push the Deflation

Button to reduce the tire pressure to the recommended
inflation pressure before continuing.

2. Disconnect the Tire Service Kit from the valve stem,

reinstall the cap on the valve stem and unplug from
12 Volt outlet.

3. Place the Tire Service Kit in its proper storage area in the

vehicle.

4. Have the tire inspected and repaired or replaced at the

earliest opportunity at an authorized dealer or tire
service center.

5. Remove the Speed Limit sticker from the steering wheel

after the tire has been repaired.

6. Replace the Sealant Bottle at your authorized dealer as

soon as possible. Refer to “Sealant Bottle Replacement”.

NOTE:

When having the tire serviced, advise the autho-

rized dealer or service center that the tire has been sealed
using the Tire Service Kit.

Sealant Bottle Replacement:

1. Unwrap the power cord.

2. Unwrap the hose.

Unwrap The Hose

7

IN CASE OF EMERGENCY

423

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for pacifica hybrid 2017

AAMP of America iSimple Operation Manual preview
iSimple
Brand: AAMP of America Pages: 6
Jeep 2009 Wrangler Quick Reference Manual preview
2009 Wrangler
Brand: Jeep Pages: 12
Jeep 2008 Liberty Installation Instructions Manual preview
2008 Liberty
Brand: Jeep Pages: 6
3SIXT 3S-1186 Operating Instructions Manual preview
3S-1186
Brand: 3SIXT Pages: 12
Jeep GLADIATOR 2022 Owner'S Manual preview
GLADIATOR 2022
Brand: Jeep Pages: 380
VDO VIEWLINE 52 MM - MOUNTING 11-09 Installation Instructions preview
VIEWLINE 52 MM - MOUNTING 11-09
Brand: VDO Pages: 4
Camoplast Polaris TATOU 4S Installation Manuallines preview
Polaris TATOU 4S
Brand: Camoplast Pages: 13
Honda 08A06-361-210 Installation Instructions preview
08A06-361-210
Brand: Honda Pages: 4
Pro-gard SAFESTOP SS0005 Installation Manual preview
SAFESTOP SS0005
Brand: Pro-gard Pages: 4
E&G Classics 1398-0502-09 Instruction Manual preview
1398-0502-09
Brand: E&G Classics Pages: 2
Fisher Body FOLDING TOP 1971 Service Manual preview
FOLDING TOP 1971
Brand: Fisher Body Pages: 37
Manik 519952T Installation Instructions preview
519952T
Brand: Manik Pages: 2
Grillo PK 1400 Operator'S Manual preview
PK 1400
Brand: Grillo Pages: 71
BMW i wallbox Installation Instructions Manual preview
i wallbox
Brand: BMW Pages: 40
wtw spectroFlex Car Adapter Operating Manual preview
spectroFlex Car Adapter
Brand: wtw Pages: 4
TATA Motors Indigo Marina Owner'S Manual & Service Book preview
Indigo Marina
Brand: TATA Motors Pages: 146
SAAS MUSCLE Series Quick Start Manual preview
MUSCLE Series
Brand: SAAS Pages: 3
Nuna Pipa TW 2 Manual preview
Pipa TW 2
Brand: Nuna Pages: 29

Brands by name

Popular brands

Load more brands