Chrysler pacifica hybrid 2017 Owner'S Manual Download Page 147 | Manualshive

Page: 147 / 604

background image

The door will slowly rotate to the full open position.

ROOF LUGGAGE RACK — IF EQUIPPED

The crossbars and side rails are designed to carry weight
on vehicles equipped with a luggage rack.

The load must

not exceed 150 lbs (68 kg), and should be uniformly
distributed over the luggage rack crossbars.

The crossbars on your vehicle are delivered stowed within
the roof rack side rails. Crossbars should always be used
whenever cargo is placed on the roof rack. Check the straps
frequently to be sure that the load remains securely at-
tached.

The roof rack does not increase the total load carrying
capacity of the vehicle. Be sure the total load of cargo inside
the vehicle plus that on the external rack does not exceed
the maximum vehicle load capacity.

Full Open Position

Roof Rack

1 — Side Rail
2 — Crossbar

3

GETTING TO KNOW YOUR VEHICLE

145

«
...
145
146
147
148
149
...
»

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for pacifica hybrid 2017

FRONT HEADLIGHT LENS COVER

Brand: Bimmer Jakes Pages: 4

Brand: Vauxhall Pages: 323

Brand: APEXi Pages: 18

Brand: Prorack Pages: 15

YARIS LIFTBACK 2009

Brand: Toyota Pages: 13

Brand: Westfalia Pages: 71

signal mirror 2005-2009 Ford Mustang

Brand: muth Pages: 9

Brand: Renault Pages: 340

Brand: METRON Pages: 4

Brand: Fast Master Products Pages: 13

RUDDER ANGLE INDICATOR

Brand: VDO Pages: 8

Brand: Chevrolet Pages: 372

2000 Oldsmobile Intrigue

Brand: Oldsmobile Pages: 348

Brand: Prorack Pages: 15

Brand: Horn Tools Pages: 12

Brand: Acura Pages: 347

Brand: Mitsubishi Pages: 490

Brand: Xforce Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands