manualshive.com logo in svg

Chrysler pacifica hybrid 2017, Owner'S Manual

The 2017 Chrysler Pacifica Hybrid comes with an informative Owner's Manual that provides detailed instructions and guidelines for maximizing the potential of your vehicle. You can easily download this manual for free from our website, ensuring that you have access to all the information you need to enjoy your Pacifica Hybrid to the fullest.

Share
Download
background image

Closing

1. Hold up the hood with one hand and with the other

hand remove the support rod from its seat and reinsert
it into the locking tab.

2. Lower the hood to approximately 12 inches (30 cm) from

the engine compartment and drop it. Make sure that the
hood is completely closed.

WARNING!

Be sure the hood is fully latched before driving your
vehicle. If the hood is not fully latched, it could open
when the vehicle is in motion and block your vision.
Failure to follow this warning could result in serious
injury or death.

CAUTION!

To prevent possible damage, do not slam the hood to
close it. Lower hood to approximately 12 inches (30 cm)
and drop the hood to close. Make sure hood is fully
closed for both latches. Never drive vehicle unless
hood is fully closed, with both latches engaged.

LIFTGATE

Opening

To Unlock/Enter The Liftgate

The liftgate may be released in several ways:

•

Overhead console liftgate button

•

Key fob

•

Outside handle

Push the liftgate button on the key fob twice within five
seconds to release the liftgate.

Unlock Liftgate Using An Key Fob

3

GETTING TO KNOW YOUR VEHICLE

129

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for pacifica hybrid 2017

Hama Pico Operating Instructions preview
Pico
Brand: Hama Pages: 2
Garmin BC 30 Owner'S Manual preview
BC 30
Brand: Garmin Pages: 2
Whispbar K783W Fitting Instructions Manual preview
K783W
Brand: Whispbar Pages: 16
Metra Electronics 99-3103 Installation Instructions preview
99-3103
Brand: Metra Electronics Pages: 2
Audi A4 2016 Quick Questions And Answers preview
A4 2016
Brand: Audi Pages: 9
Belkin WIC004 Setting Up preview
WIC004
Brand: Belkin Pages: 4
VDO DLD Wide Range II Installation Instructions Manual preview
DLD Wide Range II
Brand: VDO Pages: 84
Wagan TravelCharge Companion GO-Plus User Manual preview
TravelCharge Companion GO-Plus
Brand: Wagan Pages: 3
Monacor Carpower CAP-20 Quick Manual preview
Carpower CAP-20
Brand: Monacor Pages: 2
Jeep GLADIATOR 2022 Owner'S Manual preview
GLADIATOR 2022
Brand: Jeep Pages: 380
AddSecure Asset Light Installation Manual preview
Asset Light
Brand: AddSecure Pages: 14
Thetford SANICON TURBO 300 Operating Instructions Manual preview
SANICON TURBO 300
Brand: Thetford Pages: 25
Kia OPTIA hybrid 2020 Features & Functions Manual preview
OPTIA hybrid 2020
Brand: Kia Pages: 54
Ferve F-2024 Operating Instructions Manual preview
F-2024
Brand: Ferve Pages: 28
Horn Tools HJIMRR02FIT Mounting Instructions preview
HJIMRR02FIT
Brand: Horn Tools Pages: 12
Kolpin 1466 Product Instructions preview
1466
Brand: Kolpin Pages: 6
LedGlow Advanced Million Color Installation Instructions preview
Advanced Million Color
Brand: LedGlow Pages: 4
Chevrolet LUMINA 1995 Owner'S Manual preview
LUMINA 1995
Brand: Chevrolet Pages: 324

Brands by name

Popular brands

Load more brands