manualshive.com logo in svg

Chrysler pacifica hybrid 2017, Owner'S Manual

The 2017 Chrysler Pacifica Hybrid comes with an informative Owner's Manual that provides detailed instructions and guidelines for maximizing the potential of your vehicle. You can easily download this manual for free from our website, ensuring that you have access to all the information you need to enjoy your Pacifica Hybrid to the fullest.

Share
Download
background image

3. Align the valve notch in the wheel cover with the valve

stem on the wheel. Install the cover by hand, snapping
the cover over the two lug nuts. Do not use a hammer or
excessive force to install the cover.

4. Install the remaining lug nuts with the cone shaped end

of the nut toward the wheel. Lightly tighten the lug
nuts.

WARNING!

To avoid the risk of forcing the vehicle off the jack, do
not tighten the wheel nuts fully until the vehicle has
been lowered. Failure to follow this warning may
result in serious injury.

5. Lower the vehicle to the ground by turning the jack

handle counterclockwise.

6. Finish tightening the lug nuts. Push down on the

wrench while at the end of the handle for increased
leverage. Tighten the lug nuts in a star pattern until each
nut has been tightened twice. Refer to “Torque Specifi-
cations” in “Technical Specifications” for proper wheel
lug nut torque. If in doubt about the correct tightness,
have them checked with a torque wrench by your
authorized dealer or at a service station.

7. After 25 miles (40 km) check the lug nut torque with a

torque wrench to ensure that all lug nuts are properly
seated against the wheel.

Vehicles Without Wheel Covers

1. Mount the road tire on the axle.

Tire And Wheel Cover Or Center Cap

1 — Valve Stem

4 — Wheel Cover

2 — Valve Notch

5 — Mounting Stud

3 — Wheel Lug Nut

7

IN CASE OF EMERGENCY

413

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for pacifica hybrid 2017

Jacob Jensen Electronic Parking Disc 3 Quick Manual preview
Electronic Parking Disc 3
Brand: Jacob Jensen Pages: 2
Yakima K1005 Instructions Manual preview
K1005
Brand: Yakima Pages: 12
Horn Tools HISDMSPTRA01 Mounting Instructions preview
HISDMSPTRA01
Brand: Horn Tools Pages: 6
Xpresskit DBALL2-HYUNDAI9 Installation And Quick Reference Manual preview
DBALL2-HYUNDAI9
Brand: Xpresskit Pages: 13
RAM 2011 3500 Chassis Cab User Manual preview
2011 3500 Chassis Cab
Brand: RAM Pages: 92
Waeco MagicWatch MWE250 Installation And Operating Manual preview
MagicWatch MWE250
Brand: Waeco Pages: 172
Opel 2011 Insignia Owner'S Manual preview
2011 Insignia
Brand: Opel Pages: 254
Jeep Cherokee 1977 Owner'S Manual preview
Cherokee 1977
Brand: Jeep Pages: 136
Carcomm CHFS-34 HTC Installation Manual preview
CHFS-34 HTC
Brand: Carcomm Pages: 2
WATT CARWATT CV12-220C150 User Manual preview
CARWATT CV12-220C150
Brand: WATT Pages: 26
Cadillac ESCALADE ESV 2005 Owner'S Manual preview
ESCALADE ESV 2005
Brand: Cadillac Pages: 482
curt CM-58967 Installation Manual preview
CM-58967
Brand: curt Pages: 4
Volkswagen 1963 1500 Instruction Manual preview
1963 1500
Brand: Volkswagen Pages: 68
Westin 28-0160 Instructions preview
28-0160
Brand: Westin Pages: 3
Magneti Marelli BCF636 Installation Instruction preview
BCF636
Brand: Magneti Marelli Pages: 2
Adaptiv Mini CAM-MB6-AD User Manual preview
CAM-MB6-AD
Brand: Adaptiv Mini Pages: 4
Bracketron MULTI VEHICLE MOUNT MVM-45-05 Installation Manual preview
MULTI VEHICLE MOUNT MVM-45-05
Brand: Bracketron Pages: 4
Leer CAB HIGH SPORT BED CAP Installation Instructions & Owner'S Manual preview
CAB HIGH SPORT BED CAP
Brand: Leer Pages: 32

Brands by name

Popular brands

Load more brands