Chrysler pacifica hybrid 2017 Owner'S Manual Download Page 179 | Manualshive

Page: 179 / 604

background image

Reduced Vehicle Performance Warning Light

Red Telltale

Light

What It Means

Reduced Vehicle Performance Warning Light

This telltale illuminates when the vehicle is out of gas and only running on High Voltage battery.
Simply filling up with some gas could make the telltale go away.

NOTE:

Message indicating that the vehicle speed maybe limited, this message may be stored in

the Instrument Cluster Display “Messages” section/menu.

Yellow Telltale Lights

Anti-Lock Brake (ABS) Indicator Light

Yellow Telltale

Light

What It Means

Anti-Lock Brake (ABS) Indicator Light

This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the ignition
switch is placed in the ON/RUN position and may stay on for as long as four seconds.
If the ABS light remains on or turns on while driving, then the Anti-Lock portion of the brake
system is not functioning and service is required. However, the conventional brake system will
continue to operate normally if the brake warning light is not on.
If the ABS light is on, the brake system should be serviced as soon as possible to restore the ben-
efits of Anti-Lock Brakes. If the ABS light does not turn on when the ignition switch is placed in
the ON/RUN position, have the light inspected by an authorized dealer.

4

GETTING TO KNOW YOUR INSTRUMENT PANEL

177

«
...
177
178
179
180
181
...
»

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for pacifica hybrid 2017

Brand: AAMP of America Pages: 6

Brand: Hama Pages: 2

Brand: IAME Pages: 17

Brand: iDataLink Pages: 106

Brand: JASTEC Pages: 12

1973 Convertible

Brand: Volkswagen Pages: 80

Brand: Quadratec Pages: 8

Brand: BrandMotion Pages: 2

Brand: Thule Pages: 8

Brand: Fast Master Products Pages: 13

Brand: Kia Pages: 51

Brand: Xhorse Pages: 48

Brand: Oypla Leisure Pages: 4

Brand: STO N SHO Pages: 7

MagicWatch MWE850

Brand: Waeco Pages: 200

BEDXTENDER HD 74805-00A

Brand: AMP Research Pages: 7

Brand: TOP VEHICLE TECH Pages: 8

Brand: BrandMotion Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands