Chrysler pacifica hybrid 2017 Owner'S Manual Download Page 63 | Manualshive

Page: 63 / 604

background image

Manual Sliding Side Door

The sliding door may be opened from the inside or the
outside. Pull outward on the exterior handle to open the
sliding door. The sliding door inside handle functions by
rocking forward and back. Rocking the handle backwards
opens the door and rocking forward releases the hold open
latch in order to close the door.

NOTE:

If equipped with the power sliding side doors, refer

to “Safe Lock — If Equipped” in this section to turn the
power off for manual operation of the sliding side doors.

To keep your door operating properly, observe the follow-
ing guidelines:

•

Always open the door smoothly.

•

Avoid high impacts against the door stop when opening
the door. This is very important when your vehicle is
parked on an incline as the door will slide faster in the
downhill direction.

Side Door Handle And Lock Functions

1 — Door Handle
2 — Door Lock

3

GETTING TO KNOW YOUR VEHICLE

61

«
...
61
62
63
64
65
...
»

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for pacifica hybrid 2017

Brand: Calira Pages: 14

Brand: Happy Orange Pages: 2

Brand: JETBAG Pages: 44

Brand: Federal Signal Corporation Pages: 8

Brand: Federal Signal Corporation Pages: 8

Brand: Code 3 Pages: 8

Brand: Haibang Pages: 6

2012 Truck Chassis cab

Brand: RAM Pages: 506

Brand: Audiovox Pages: 24

Brand: Mercedes-Benz Pages: 2

Brand: Westin Pages: 2

Brand: ULTIMATE SPEED Pages: 6

Brand: Saab Pages: 15

Brand: Streetwize Pages: 4

Brand: Anker Technology Pages: 8

Brand: Ford Pages: 52

Brand: TATA Motors Pages: 308

Charger SRT 392 2017

Brand: Dodge Pages: 576

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands