Chrysler pacifica hybrid 2017 Owner'S Manual Download Page 301 | Manualshive

Page: 301 / 604

background image

WARNING!

Continued operation with reduced assist could pose a
safety risk to yourself and others. Service should be
obtained as soon as possible.

If the “SERVICE POWER STEERING

⬙

OR

⬙

POWER STEERING ASSIST OFF - SERVICE SYS-

TEM” message and a steering wheel icon are
displayed on the instrument cluster screen, it

indicates that the vehicle needs to be taken to the dealer for
service. It is likely the vehicle has lost power steering
assistance. Refer to “Instrument Cluster Display” in “Getting
To Know Your Instrument Panel” for further information.

NOTE:

•

Even if the power steering assistance is no longer
operational, it is still possible to steer the vehicle. Under
these conditions there will be a substantial increase in
steering effort, especially at low speeds and during
parking maneuvers.

•

The power steering system is fully electric; it requires no
power steering fluid.

•

If the condition persists, see your authorized dealer for
service.

SPEED CONTROL — IF EQUIPPED

When engaged, the Speed Control takes over accelerator
operations at speeds greater than 25 mph (40 km/h).

The Speed Control buttons are located on the right side of
the steering wheel.

Speed Control Buttons

1 — On/Off

4 — SET-/Decel

2 — SET+/Accel

5 — CANC/Cancel

3 — RES/Resume

6

STARTING AND OPERATING

299

«
...
299
300
301
302
303
...
»

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for pacifica hybrid 2017

Brand: PEUGEOT Pages: 128

Brand: Schumacher Electric Pages: 87

2009 ESCALADE ESV

Brand: Cadillac Pages: 602

Brand: walser Pages: 24

Brand: NavLinkz Pages: 21

Brand: Oldsmobile Pages: 2

Brand: Toyota Pages: 600

Brand: Vangear Pages: 5

Brand: Safe Fleet Pages: 20

Brand: ConWys AG Pages: 16

Brand: FORM FIT Pages: 2

Brand: Master Tailgaters Pages: 10

Brand: Oldsmobile Pages: 276

Brand: Volkswagen Pages: 32

Brand: Pogo Pages: 40

1995 C/K Pickup

Brand: Chevrolet Pages: 483

Brand: HOLDEN Pages: 330

Brand: Mazda Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands