Chrysler pacifica hybrid 2017 Owner'S Manual Download Page 349 | Manualshive

Page: 349 / 604

background image

system will cancel and the instrument cluster display
will instruct the driver to complete the maneuver manu-
ally.

The ParkSense Active Park Assist system will only operate
and search for a parking space when the following condi-
tions are present:

•

The gear position is in DRIVE.

•

The ignition is in the RUN position.

•

The ParkSense Active Park Assist switch is activated.

•

The Driver’s door is closed.

•

The liftgate is closed.

•

Vehicle speed is less than 15 mph (25 km/h).

NOTE:

If the vehicle is driven above approximately

15 mph (25 km/h), the instrument cluster display will
instruct the driver to slow down. If the vehicle is driven
above approximately 18 mph (30 km/h), the system will
cancel. The driver must then reactivate the system by
pushing the ParkSense Active Park Assist switch.

•

The outer surface and the underside of the front and rear
fascias/bumpers are clean and clear of snow, ice, mud,
dirt or other obstruction.

When pushed, the LED on the ParkSense Active Park
Assist switch will blink momentarily, and then the LED
will turn OFF if any of the above conditions are not
present.

Parallel Parking Space Assistance Operation/
Display

When the ParkSense Active Park Assist system is enabled
the “Active ParkSense Searching - Push OK for Perpen-
dicular Park” message will appear in the instrument clus-
ter display. You may switch to perpendicular parking if
you desire. Push the OK button on the left side steering
wheel switch to change your parking space setting.

NOTE:

•

When searching for a parking space, use the turn signal
indicator to select which side of the vehicle you want to
perform the parking maneuver. The ParkSense Active
Park Assist system will automatically search for a park-
ing space on the passenger’s side of the vehicle if the
turn signal is not activated.

•

The driver needs to make sure that the selected parking
space for the maneuver remains free and clear of any
obstructions (e.g. pedestrians, bicycles, etc.).

6

STARTING AND OPERATING

347

«
...
347
348
349
350
351
...
»

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for pacifica hybrid 2017

Brand: JAC Pages: 70

Brand: Hama Pages: 2

Brand: Abarth Pages: 36

Brand: Yakima Pages: 12

Brand: JEHNERT SOUND DESIGN Pages: 8

Experience Series

Brand: Rainbow Pages: 19

Brand: Yakima Pages: 12

Brand: EEZ RV Pages: 31

MAGNUM RT Series

Brand: Raptor Series Pages: 6

Brand: TBC Pages: 12

Brand: Prorack Pages: 14

Brand: Subaru Pages: 298

Brand: Saab Pages: 92

Brand: A-rival Pages: 23

Brand: Black Horse Off Road Pages: 7

Brand: Vangear Pages: 5

Brand: Safe Fleet Pages: 20

Brand: Curtis Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands