Chrysler pacifica hybrid 2017 Owner'S Manual Download Page 398

Page: 398 / 604

4. Install the front turn signal lamp socket assembly into

the housing, and rotate the front turn signal lamp socket
clockwise to lock it in place.

Front And Rear Side Marker Lamps

1. Remove the three fasteners from the inner wheel liner

and carefully peel back liner for access.

2. Firmly grasp the front side marker lamp socket and

rotate 1/4 turn counterclockwise to remove it from the
lamp assembly.

3. Remove bulb from the front side marker lamp socket

and replace with a new bulb.

4. Install front side marker lamp socket in lamp assembly

and rotate 1/4 turn clockwise to lock into place.

5. Position the inner wheel liner in place and install the

three fasteners.

Inner Wheel Liner Fasteners

Front Side Marker Lamp Bulb Removal

396

IN CASE OF EMERGENCY

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for pacifica hybrid 2017

Reviews:

Related manuals for pacifica hybrid 2017

Brands by name

Popular brands

Chrysler pacifica hybrid 2017, Owner'S Manual

Search results

Summary of Contents for pacifica hybrid 2017

Reviews:

Related manuals for pacifica hybrid 2017

Brands by name

Popular brands