Chrysler pacifica hybrid 2017 Owner'S Manual Download Page 479 | Manualshive

Page: 479 / 604

background image

Run Flat Tires — If Equipped

Run Flat tires allow you the capability to drive 50 miles
(80 km) at 50 mph (80 km/h) after a rapid loss of inflation
pressure. This rapid loss of inflation is referred to as the
Run Flat mode. A Run Flat mode occurs when the tire
inflation pressure is of/or below 14 psi (96 kPa). Once a
Run Flat tire reaches the run flat mode it has limited
driving capabilities and needs to be replaced immediately.
A Run Flat tire is not repairable.

It is not recommended driving a vehicle loaded at full
capacity or to tow a trailer while a tire is in the run flat
mode.

See the tire pressure monitoring section for more informa-
tion.

Tire Spinning

When stuck in mud, sand, snow, or ice conditions, do not
spin your vehicle’s wheels above 30 mph (48 km/h) or for
longer than 30 seconds continuously without stopping.

Refer to “Freeing A Stuck Vehicle” in “In Case Of Emer-
gency” for further information.

WARNING!

Fast spinning tires can be dangerous. Forces generated
by excessive wheel speeds may cause tire damage or
failure. A tire could explode and injure someone. Do
not spin your vehicle’s wheels faster than 30 mph
(48 km/h) for more than 30 seconds continuously when
you are stuck, and do not let anyone near a spinning
wheel, no matter what the speed.

8

SERVICING AND MAINTENANCE

477

«
...
477
478
479
480
481
...
»

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for pacifica hybrid 2017

Brand: Cadillac Pages: 3

Brand: Cadillac Pages: 12

Brand: Cadillac Pages: 106

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 326

Brand: Cadillac Pages: 28

ESCALADE - BROCHURE 2009

Brand: Cadillac Pages: 602

ESCALADE ESV 2004

Brand: Cadillac Pages: 20

ESCALADE EXT 2005

Brand: Cadillac Pages: 460

CT6 SUPER CRUISE 2018

Brand: Cadillac Pages: 8

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 337

Brand: Vintage Air Pages: 28

Car Top Duffle Bag

Brand: Rightline Gear Pages: 2

Brand: Audi Pages: 9

Brand: Belkin Pages: 4

01 29 9 416 497

Brand: BMW Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands