manualshive.com logo in svg

Chrysler pacifica hybrid 2017, Owner'S Manual

The 2017 Chrysler Pacifica Hybrid comes with an informative Owner's Manual that provides detailed instructions and guidelines for maximizing the potential of your vehicle. You can easily download this manual for free from our website, ensuring that you have access to all the information you need to enjoy your Pacifica Hybrid to the fullest.

Share
Download
background image

WARNING!

Fast spinning tires can be dangerous. Forces generated
by excessive wheel speeds may cause damage, or even
failure, of the axle and tires. A tire could explode and
injure someone. Do not spin your vehicle’s wheels
faster than 30 mph (48 km/h) or for longer than 30
seconds continuously without stopping when you are
stuck and do not let anyone near a spinning wheel, no
matter what the speed.

CAUTION!

•

When “rocking” a stuck vehicle by shifting between
DRIVE and REVERSE, do not spin the wheels faster
than 15 mph (24 km/h), or drivetrain damage may result.

•

Spinning the wheels too fast may lead to transmis-
sion overheating and failure. It can also damage the
tires. Do not spin the wheels above 30 mph (48 km/h)
while in gear (no transmission shifting occurring).

TOWING A DISABLED VEHICLE

This section describes procedures for towing a disabled
vehicle using a commercial towing service.

Towing Condition

Wheel OFF The Ground

ALL MODELS

Flat Tow

NONE

NOT ALLOWED

Wheel Lift Or Dolly Tow

Front

OK

Rear

NOT ALLOWED

Flatbed

ALL

BEST METHOD

Proper towing or lifting equipment is required to prevent
damage to your vehicle. Use only tow bars and other
equipment designed for this purpose, following equipment

manufacturer’s instructions. Use of safety chains is man-
datory. Attach a tow bar or other towing device to main

7

IN CASE OF EMERGENCY

431

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for pacifica hybrid 2017

cam 2850 Mounting Instructions preview
2850
Brand: cam Pages: 2
Dapper Lighting 575 Install Manual preview
575
Brand: Dapper Lighting Pages: 2
Vauxhall Meriva Quick Reference Manual preview
Meriva
Brand: Vauxhall Pages: 2
Vauxhall Ampera Quick Reference Manual preview
Ampera
Brand: Vauxhall Pages: 2
Vauxhall 2012 Agila Quick Reference Manual preview
2012 Agila
Brand: Vauxhall Pages: 2
Vauxhall 2013 Mokka Owner'S Manual preview
2013 Mokka
Brand: Vauxhall Pages: 209
VBC Racing WildFire Instruction Manual preview
WildFire
Brand: VBC Racing Pages: 34
Vauxhall 2013 Corsa Infotainment system Quick Reference Manual preview
2013 Corsa Infotainment system
Brand: Vauxhall Pages: 2
Vauxhall 2010 Astra Quick Reference Manual preview
2010 Astra
Brand: Vauxhall Pages: 2
Vauxhall Antara Owner'S Manual preview
Antara
Brand: Vauxhall Pages: 236
Yakima Q46 Installation Instructions preview
Q46
Brand: Yakima Pages: 4
OEM Audio Reference Series Manual preview
Reference Series
Brand: OEM Audio Pages: 29
Kia CADENZA 2019 Features & Functions Manual preview
CADENZA 2019
Brand: Kia Pages: 54
Metra Electronics 99-9001 Installation Instructions preview
99-9001
Brand: Metra Electronics Pages: 2
Romik 2137 2D Installation Instructions Manual preview
2137 2D
Brand: Romik Pages: 6
Pet Gear TRI-FOLD PG9300RF Instruction Manual preview
TRI-FOLD PG9300RF
Brand: Pet Gear Pages: 4
v.LOGiC V5-CIC-E-PNP Manual preview
V5-CIC-E-PNP
Brand: v.LOGiC Pages: 22
Vauxhall Crossland X 2017 Owner'S Manual preview
Crossland X 2017
Brand: Vauxhall Pages: 245

Brands by name

Popular brands

Load more brands