Chrysler pacifica hybrid 2017 Owner'S Manual Download Page 163 | Manualshive

Page: 163 / 604

background image

•

If one or more tires have low pressure, “Inflate Tire To
XX” is displayed with the vehicle ICON, and the tire
pressure values in each corner of the ICON with the
pressure value of the low tire displayed in a different
color than the other tire pressure value.

•

If the Tire Pressure system requires service, “Service Tire
Pressure System” is displayed.

•

Tire PSI is an information only function and cannot be
reset.

•

Refer to “Tire Pressure Monitoring System (TPMS)”
under “Safety” for further information.

•

Coolant Temperature

Displays the actual coolant temperature.

•

Oil Temperature

Displays the actual oil temperature.

•

Oil Pressure

Displays the actual oil pressure.

•

Oil Life (Hold OK Button To Reset)

•

The “Hold OK to Reset” instruction will be displayed at
all times, but the following conditions will need to be
met in order to reset Oil Life:

The vehicle must be off

The ignition must be in the ON/RUN position

•

If the conditions are met, holding the

OK

button will

reset the gauge and the numeric display will return to
100%.

•

If the conditions are not met, a popup message will
display for 5 seconds, describing the required condi-
tions, and then the Oil Life screen will reappear.

•

Battery Voltage

Displays the actual battery voltage.

•

Engine Hours — If Equipped

Displays the number of hours of engine operation.

Driver Assist — If Equipped

Push and release the

up

or

down

arrow button until Driver

Assist is highlighted in the instrument cluster display.

•

Adaptive Cruise Control and LaneSense:

•

Driver Assist Screen shows the current status of both
the ACC and the LaneSense systems

•

Popup messages also indicate the status of the system
and/or the conditions that need to be met

4

GETTING TO KNOW YOUR INSTRUMENT PANEL

161

«
...
161
162
163
164
165
...
»

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for pacifica hybrid 2017

Brand: Back View Pages: 168

Brand: Masterack Pages: 4

Brand: Over Armour Offroad Pages: 5

Brand: Honda Pages: 32

Brand: V8 equipment Pages: 17

Brand: Subaru Pages: 21

Brand: Whipple Pages: 3

Brand: Actia Pages: 102

Brand: BMW Pages: 38

Brand: Caltrend Pages: 3

Brand: Black+Decker Pages: 21

Brand: Beeper Pages: 20

Brand: OHIOSTEEL Pages: 2

MagicSafe MSG150

Brand: Waeco Pages: 20

Brand: MiX Telematics Pages: 39

Brand: SuperATV Pages: 2

Brand: Audiovox Electronics Pages: 12

Brand: Edelbrock Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands