manualshive.com logo in svg

Chrysler pacifica hybrid 2017, Owner'S Manual

The 2017 Chrysler Pacifica Hybrid comes with an informative Owner's Manual that provides detailed instructions and guidelines for maximizing the potential of your vehicle. You can easily download this manual for free from our website, ensuring that you have access to all the information you need to enjoy your Pacifica Hybrid to the fullest.

Share
Download
background image

Carefully move the vehicle to a level 1 or Level 2 charge
location. While the vehicle is being moved, the external
12V power must remained connected to the vehicle
jump posts.

NOTE:

Be careful when moving the vehicle - ensure that

control of the vehicle is maintained. Also, ensure that
vehicle is secured to prevent unintentional movement
during and after moving the vehicle. If the external 12V
power becomes disconnected from the vehicle jump posts
or there is an interruption of the 12V power while moving
the vehicle, the vehicle’s transmission may engage PARK.

When the vehicle is at the charging location, shift the
transmission back to PARK, apply the electric park brake,
and start the high voltage battery charging. Once the
vehicle has been secured against unintentional movement
and high voltage battery charging has been initiated, the
jumper cables can be removed from the vehicle jump posts.

Jump-starting can be dangerous if done improperly so
please follow the procedures in this section carefully.

NOTE:

When using a portable battery booster pack, follow

the manufacturer’s operating instructions and precautions.

WARNING!

Do not attempt jump starting if the battery is frozen. It
could rupture or explode and cause personal injury.

CAUTION!

Do not use a portable battery booster pack or any other
booster source with a system voltage greater than 12
Volts or damage to the battery, starter motor, alternator
or electrical system may occur.

Preparations For Jump-Start

The remote battery posts in your vehicle is located on the
left side of the engine compartment.

426

IN CASE OF EMERGENCY

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for pacifica hybrid 2017

Back View RV-250 User Manual preview
RV-250
Brand: Back View Pages: 168
ULTIMATE SPEED CARBON Assembly And Safety Advice preview
CARBON
Brand: ULTIMATE SPEED Pages: 19
Kargo Master 40131 Installation Manual preview
40131
Brand: Kargo Master Pages: 5
Napoli NPL-TV 7874 DIGITAL Instruction Manual preview
NPL-TV 7874 DIGITAL
Brand: Napoli Pages: 20
Whispbar K561W Fitting Instructions Manual preview
K561W
Brand: Whispbar Pages: 15
UGREEN Car Cup Holder Phone Mount Manual preview
Car Cup Holder Phone Mount
Brand: UGREEN Pages: 9
Audiovox Code Alarm PROFESSIONAL SERIES CA 5550SST Owner'S Manual preview
Code Alarm PROFESSIONAL SERIES CA 5550SST
Brand: Audiovox Pages: 14
Enduro autoSteady AS101 User Manual preview
autoSteady AS101
Brand: Enduro Pages: 48
AA Products RB0007 Instruction Manual preview
RB0007
Brand: AA Products Pages: 6
Yakima Landing Pad 24 Quick Start Manual preview
Landing Pad 24
Brand: Yakima Pages: 11
Van Guard VG273 Fitting Instructions preview
VG273
Brand: Van Guard Pages: 3
EUFAB 16465 Operating Instructions Manual preview
16465
Brand: EUFAB Pages: 12
Kogan CERTA CTCVINCVR14A User Manual preview
CERTA CTCVINCVR14A
Brand: Kogan Pages: 4
Calix M5T 204 Assembly Instructions preview
M5T 204
Brand: Calix Pages: 4
Green Valley 601951 Instructions Manual preview
601951
Brand: Green Valley Pages: 17
ZENEC ZE-RVC85WA Mounting Instructions preview
ZE-RVC85WA
Brand: ZENEC Pages: 2
U.S. General 95187 Instruction Sheet preview
95187
Brand: U.S. General Pages: 3
Prorack K890 Fitting Instructions Manual preview
K890
Brand: Prorack Pages: 15

Brands by name

Popular brands

Load more brands