Chrysler pacifica hybrid 2017 Owner'S Manual Download Page 73 | Manualshive

Page: 73 / 604

background image

WARNING!

(Continued)

•

Seats should be adjusted before fastening the seat
belts and while the vehicle is parked. Serious injury
or death could result from a poorly adjusted seat belt.

Manual Recline

To recline, lean forward slightly, lift the lever, and push
back to the desired position and release the lever. Lean
forward and lift the lever to return the seatback to its
normal position. Using body pressure, lean forward and
rearward on the seat to be sure the seatback has latched.

WARNING!

Do not ride with the seatback reclined so that the
shoulder belt is no longer resting against your chest. In
a collision you could slide under the seat belt, which
could result in serious injury or death.

Fold-Flat

To fold the seat, lift the recliner lever to the full upward
position and push the seatback forward until it rests on the
seat cushion.

Recline Lever

Fold-Flat Seat Recline Lever

3

GETTING TO KNOW YOUR VEHICLE

71

«
...
71
72
73
74
75
...
»

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for pacifica hybrid 2017

Brand: Panasonic Pages: 2

CYRC50U - UNIVERSAL REAR-VIEW CAMERA

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 12

Brand: Raven Pages: 24

Brand: Weather Guard Pages: 4

Brand: DEFA Pages: 9

Slim Line LED Light Grille Kit

Brand: rough country Pages: 8

Brand: ULTIMATE SPEED Pages: 21

Brand: Fast Master Products Pages: 13

Brand: Westfalia Pages: 10

Brand: JKS Pages: 6

Brand: Volvo Pages: 42

Brand: FORM FIT Pages: 2

Brand: Huf Pages: 6

Prime Design VBI-FT31B

Brand: Safe Fleet Pages: 12

Brand: Speedtech Pages: 12

Brand: Yakima Pages: 10

Brand: DIGITAL DELAY Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands