Chrysler pacifica hybrid 2017 Owner'S Manual Download Page 162

Page: 162 / 604

With KeySense in use there will be multiple associated
messages shown in the following table:

Setting

Instrument Cluster Display Message

None – With vehicle ignition

“KeySense in use. Max vehicle speed set to xx MPH/or km/h”

Max Vehicle Speed

•

“Max speed reached. KeySense in use” supported by a chime

•

“Approaching max speed xx MPH/km” supported by a chime

Start Up Fuel Alert message

“Range to empty xxx miles or km”

Early Low Fuel Alert Message

“Fuel Low”

ParkSense

“Feature cannot be disabled. KeySense in use”

Blind Spot

“Feature cannot be disabled. KeySense in use”

Forward Collision Warning

“Feature cannot be disabled. KeySense in use”

Instrument Cluster Display Menu Items

NOTE:

The Instrument Cluster Display menu items dis-

play in the center of the instrument cluster. Menu items
may vary depending on your vehicle features.

Speedometer

Push and release the

down

arrow button until

Speedometer is highlighted in the instrument cluster dis-
play. Push and release the

button to toggle between

MPH and km/h.

Vehicle Info

Push and release the

down

arrow button until

Vehicle Info is highlighted in the instrument cluster dis-
play. Push the

left

right

arrow button to scroll through

the following information submenus:

•

Tire Pressure

•

If tire pressure is

for all tires, a vehicle ICON is

displayed with tire pressure values in each corner of the
ICON.

160

GETTING TO KNOW YOUR INSTRUMENT PANEL

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for pacifica hybrid 2017

Reviews:

Related manuals for pacifica hybrid 2017

Brands by name

Popular brands

Chrysler pacifica hybrid 2017, Owner'S Manual

Search results

Summary of Contents for pacifica hybrid 2017

Reviews:

Related manuals for pacifica hybrid 2017

Brands by name

Popular brands