manualshive.com logo in svg

Chrysler pacifica hybrid 2017, Owner'S Manual

The 2017 Chrysler Pacifica Hybrid comes with an informative Owner's Manual that provides detailed instructions and guidelines for maximizing the potential of your vehicle. You can easily download this manual for free from our website, ensuring that you have access to all the information you need to enjoy your Pacifica Hybrid to the fullest.

Share
Download
background image

WARNING!

Driving a vehicle with the red brake light on is
dangerous. Part of the brake system may have failed. It
will take longer to stop the vehicle. You could have a
collision. Have the vehicle checked immediately.

Vehicles equipped with the Anti-Lock Brake System (ABS)
are also equipped with Electronic Brake Force Distribution
(EBD). In the event of an EBD failure, the Brake Warning
Light will turn on along with the ABS Light. Immediate
repair to the ABS system is required.

Operation of the Brake Warning Light can be checked by
turning the ignition switch from the OFF position to the
ON/RUN position. The light should illuminate for ap-
proximately two seconds. The light should then turn off
unless the parking brake is applied or a brake fault is
detected. If the light does not illuminate, have the light
inspected by an authorized dealer.

The light also will turn on when the parking brake is
applied with the ignition switch in the ON/RUN position.

NOTE:

This light shows only that the parking brake is

applied. It does not show the degree of brake application.

Battery Charge Warning Light

Red Telltale

Light

What It Means

Battery Charge Warning Light (12 Volt Battery)

This light illuminates when the battery is not charging properly. If it stays on while the vehicle is
running, there may be a malfunction with the charging system. Contact your authorized dealer as
soon as possible. This indicates a possible problem with the electrical system or a related compo-
nent.
If jump starting is required, refer to “Jump-Starting” in “In Case Of Emergency.”

4

GETTING TO KNOW YOUR INSTRUMENT PANEL

171

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for pacifica hybrid 2017

Vauxhall Meriva Quick Reference Manual preview
Meriva
Brand: Vauxhall Pages: 2
Vauxhall Ampera Quick Reference Manual preview
Ampera
Brand: Vauxhall Pages: 2
Vauxhall 2012 Agila Quick Reference Manual preview
2012 Agila
Brand: Vauxhall Pages: 2
Vauxhall 2013 Mokka Owner'S Manual preview
2013 Mokka
Brand: Vauxhall Pages: 209
VBC Racing WildFire Instruction Manual preview
WildFire
Brand: VBC Racing Pages: 34
Vauxhall 2013 Corsa Infotainment system Quick Reference Manual preview
2013 Corsa Infotainment system
Brand: Vauxhall Pages: 2
Vauxhall 2010 Astra Quick Reference Manual preview
2010 Astra
Brand: Vauxhall Pages: 2
Vauxhall Antara Owner'S Manual preview
Antara
Brand: Vauxhall Pages: 236
Ford 2008 Mustang Quick Reference Manual preview
2008 Mustang
Brand: Ford Pages: 2
Suzuki Movano Owner'S Manual preview
Movano
Brand: Suzuki Pages: 353
Torklift F2012 Installation Instructions Manual preview
F2012
Brand: Torklift Pages: 16
TUFLOC Dodge Charger TufBox Installation Instructions Manual preview
Dodge Charger TufBox
Brand: TUFLOC Pages: 6
Curt Manufacturing 31048 Installation Instructions Manual preview
31048
Brand: Curt Manufacturing Pages: 6
tams elektronik 54-01016 Manual preview
54-01016
Brand: tams elektronik Pages: 44
Thule 1430 Kit Instructions Manual preview
1430 Kit
Brand: Thule Pages: 8
walser ULTIMATE SPEED 296713 Assembly And Safety Advice preview
ULTIMATE SPEED 296713
Brand: walser Pages: 10
Mercedes-Benz 2009 E-Class Manual preview
2009 E-Class
Brand: Mercedes-Benz Pages: 373
Xpresskit DBALL2-HK7 Installation Manual preview
DBALL2-HK7
Brand: Xpresskit Pages: 18

Brands by name

Popular brands

Load more brands