Chrysler pacifica hybrid 2017 Owner'S Manual Download Page 50 | Manualshive

Page: 50 / 604

background image

WARNING!

(Continued)

•

Do not leave the key fob in or near the vehicle, or in
a location accessible to children, and do not leave the
ignition of a vehicle equipped with Keyless Enter-
N-Go in the RUN mode. A child could operate power
windows, other controls, or move the vehicle.

•

Do not leave children or animals inside parked
vehicles in hot weather. Interior heat build-up may
cause serious injury or death.

CAUTION!

An unlocked vehicle is an invitation. Always remove
the key from the ignition and lock all the doors when
leaving the vehicle unattended.

NOTE:

If the brake is pressed and the ignition is placed in

the RUN position, the instrument cluster will not display
the Ready state. When the Electric Vehicle Supply Equip-
ment (EVSE) is unplugged from the vehicle, it will go into
the “Ready” state. If the vehicle is not shifted out of Park 30
minutes following being unplugged, the vehicle will dis-
able the “Ready” state and the Ignition will go to RUN
mode. After an additional 30 minutes with no change in
Ignition status, the Ignition shall go to OFF and the vehicle

shall power down. For further information, refer to

⬙

Start-

ing Procedures

⬙

in

⬙

Starting And Operating

⬙

for further

information,

REMOTE STARTING SYSTEM — IF EQUIPPED

NOTE: Remote start on Hybrid while plugged in may
not always start the engine. Temperature dependent.

This system uses the key fob to start the vehicle
conveniently from the outside while still main-
taining security. The system has a range of 328 ft
(100 m).

The Remote Starting System also activates the Climate
Control, vented seats (if equipped) in temperatures above
80° F (26.7° C), the optional heated seats, optional heated
steering wheel, optional heated mirrors and rear defroster
in temperatures below 40° F (4.4° C).

NOTE:

•

Obstructions between the vehicle and key fob may
reduce this range.

•

While plugged in the remote start feature for the vehicle
may not always start the engine. Temperature depen-
dent.

48

GETTING TO KNOW YOUR VEHICLE

«
...
48
49
50
51
52
...
»

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for pacifica hybrid 2017

GRAND CHEROKEE 2023

Brand: Jeep Pages: 108

HOIST-A-TOP JL CRANK

Brand: Lange Originals Pages: 13

Brand: Chevrolet Pages: 356

Brand: Ford Pages: 272

Brand: Pontiac Pages: 376

Brand: Jeep Pages: 712

10-8002-C11998B

Brand: Saleen Pages: 12

2013 Buick Verano

Brand: Buick Pages: 5

Brand: TATA Motors Pages: 156

Brand: Voxoa Pages: 48

Alloy Rugged Ridge X-Clamp

Brand: Omix-Ada Pages: 2

Brand: Dodge Pages: 3

Brand: Draw tite Pages: 4

Brand: FORM FIT Pages: 2

Brand: Chevrolet Pages: 46

2013 Zafira Tourer

Brand: Vauxhall Pages: 289

2001 Accord Sedan

Brand: Honda Pages: 372

Brand: Imiola HAK-POL Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands