Chrysler pacifica hybrid 2017 Owner'S Manual Download Page 160 | Manualshive

Page: 160 / 604

background image

Oil Life Reset

•

Your vehicle is equipped with an engine oil change
indicator system. The “Oil Change Due” message will
display for approximately five seconds after a single
chime has sounded, to indicate the next scheduled oil
change interval. The engine oil change indicator system
is duty cycle based, which means the engine oil change
interval may fluctuate, dependent upon your personal
driving style.

•

Unless reset, this message will continue to display each
time the ignition is cycled to the ON/RUN position. To
reset the oil change indicator system (after performing
the scheduled maintenance) refer to the following pro-
cedure.

•

To reset the oil change indicator after performing the
scheduled maintenance, refer to the following proce-
dure.

Keyless Enter-N-Go — Ignition

Without pressing the brake pedal, push the ENGINE
START/STOP button and place the ignition in the ON/
RUN position (do not start the vehicle.)

1. Push the

OK

button to enter the instrument cluster

display menu screen.

2. Push and release the

down

arrow button to access the

”Oil Life” menu screen.

3. Push the

left

arrow button or right arrow button to

access the “Vehicle Info” submenu.

Keyless Push Button Ignition

158

GETTING TO KNOW YOUR INSTRUMENT PANEL

«
...
158
159
160
161
162
...
»

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for pacifica hybrid 2017

Brand: Subaru Pages: 21

MILSCO KIT# C746700

Brand: K&M Pages: 2

Brand: Car-Interface Pages: 25

2 Bike Carrier 977

Brand: Thule Pages: 6

Brand: RAM Pages: 616

Brand: Nav TV Pages: 9

Brand: Honda Pages: 81

Brand: ULTIMATE SPEED Pages: 50

Brand: Toyota Pages: 636

Brand: Caltrend Pages: 3

Brand: Carcomm Pages: 2

Brand: Subaru Pages: 32

Brand: Fab Fours Pages: 21

Brand: Air Lift Pages: 28

Brand: Dolphin Pages: 16

Brand: Brink Pages: 21

Airgo Active cushion / Comfort

Brand: TOGU Pages: 2

2008 Savana Van

Brand: GMC Pages: 402

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands