Chrysler pacifica hybrid 2017 Owner'S Manual Download Page 205 | Manualshive

Page: 205 / 604

background image

When the vehicle is started, the BSM warning light will
momentarily illuminate in both outside rear view mirrors
to let the driver know that the system is operational. The
BSM system sensors operate when the vehicle is in any
forward gear or REVERSE and enters stand-by mode when
the vehicle is in PARK.

The BSM detection zone covers approximately one lane
width on both sides of the vehicle 12 ft (3.8 m). The zone
length starts at the outside rear view mirror and extends
approximately 10 ft (3 m) beyond the rear bumper of the
vehicle. The BSM system monitors the detection zones on
both sides of the vehicle when the vehicle speed reaches
approximately 6 mph (10 km/h) or higher and will alert
the driver of vehicles in these areas.

NOTE:

The BSM system DOES NOT alert the driver about

rapidly approaching vehicles that are outside the detection
zones.

The area on the rear fascia where the radar sensors are
located must remain free of snow, ice, and dirt/road
contamination so that the BSM system can function prop-
erly. Do not block the area of the rear fascia where the radar
sensors are located with foreign objects (bumper stickers,
bicycle racks, etc.).

Rear Detection Zones

5

SAFETY

203

«
...
203
204
205
206
207
...
»

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for pacifica hybrid 2017

Brand: LaserTrack Pages: 12

Brand: Camcar Pages: 6

Brand: ABL Pages: 4

51 47 0 027 792

Brand: BMW Pages: 7

Brand: Ford Pages: 728

Brand: Westin Pages: 5

Brand: Prorack Pages: 15

Brand: QA1 Pages: 3

transit connect 2012

Brand: Ford Pages: 299

Brand: FIRRAK Pages: 12

Brand: KAP Pages: 22

2002 Accord Coupe

Brand: Honda Pages: 367

Brand: HAKR Pages: 2

Brand: NavLinkz Pages: 26

Brand: FALCON RIDGE Pages: 8

Brand: Subaru Pages: 9

Brand: Prorack Pages: 15

EXPLORER A90095

Brand: SportRack Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands