Chrysler pacifica hybrid 2017 Owner'S Manual Download Page 175 | Manualshive

Page: 175 / 604

background image

Electronic Throttle Control (ETC) Warning Light

Red Telltale

Light

What It Means

Electronic Throttle Control (ETC) Warning Light

This light informs you of a problem with the Electronic Throttle Control (ETC) system. If a prob-
lem is detected while the vehicle is running, the light will either stay on or flash depending on
the nature of the problem. Cycle the ignition when the vehicle is safely and completely stopped
and the transmission is placed in the PARK position. The light should turn off. If the light re-
mains on with the vehicle under power, your vehicle will usually be drivable; however, see an
authorized dealer for service as soon as possible.
If the light continues to flash when the vehicle is under power, immediate service is required and
you may experience reduced performance, and your vehicle may require towing. The light will
come on when the ignition is placed in the ON/RUN position and remain on briefly as a bulb
check. If the light does not come on during starting, have the system checked by an authorized
dealer.

Oil Temperature Warning Light

Red Telltale

Light

What It Means

Oil Temperature Warning Light

This telltale indicates vehicle oil temperature is high. If the light turns on while driving, stop the
vehicle and shut off the engine as soon as possible.

4

GETTING TO KNOW YOUR INSTRUMENT PANEL

173

«
...
173
174
175
176
177
...
»

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for pacifica hybrid 2017

Green Motion DC 22

Brand: Eaton Pages: 65

Brand: Wagan Pages: 12

Brand: HALE Pages: 44

Brand: FormFit Pages: 2

Brand: PEUGEOT Pages: 128

Brand: Schumacher Electric Pages: 87

2009 ESCALADE ESV

Brand: Cadillac Pages: 602

Brand: Trailboss Pages: 8

Brand: Phonocar Pages: 2

Brand: Pacbrake Pages: 6

Brand: iDataLink Pages: 6

Brand: Grillo Pages: 71

Brand: CARFACE Pages: 16

Brand: Curt Group Pages: 3

Brand: Juna Pages: 10

PRO-FLO XT 3527

Brand: Edelbrock Pages: 39

Brand: Revelation Pages: 4

Brand: APS Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands