Chrysler pacifica hybrid 2017 Owner'S Manual Download Page 45 | Manualshive

Page: 45 / 604

background image

Programming Additional Key Fob

If you do not have a programmed key fob, contact your
authorized dealer for details.

Request For Additional Remote Controls

NOTE:

Only key fobs that are programmed to the vehicle

electronics can be used to start and operate the vehicle.
Once a key fob is programmed to a vehicle, it cannot be
programmed to any other vehicle.

CAUTION!

•

Always remove the key fobs from the vehicle and
lock all doors when leaving the vehicle unattended.

•

For vehicles equipped with Keyless Enter-N-Go —
Ignition, always remember to place the ignition in
the OFF position.

Duplication of key fobs may be performed at an authorized
dealer. This procedure consists of programming a blank
key fob to the vehicle electronics. A blank key fob is one
that has never been programmed.

NOTE:

When having the Sentry Key Immobilizer System

serviced, bring all vehicle keys with you to an authorized
dealer.

KeySense Features — If Equipped

This feature provides the vehicle owner with the ability to
identify a specific vehicle key for which a customized
category of vehicle settings can be applied to determine the
driving experience for other drivers of the vehicle. The
vehicle settings are protected by a unique 4-digit PIN,
which the vehicle owner creates when accessing the spe-
cific settings for the first time.

3

GETTING TO KNOW YOUR VEHICLE

43

«
...
43
44
45
46
47
...
»

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for pacifica hybrid 2017

Brand: PAC Pages: 4

Brand: PAC Pages: 4

Brand: PAC Pages: 8

Brand: PAC Pages: 5

Brand: Whispbar Pages: 77

Brand: Whispbar Pages: 15

Brand: WABCO Pages: 32

MAGNUM RT Series

Brand: Raptor Series Pages: 6

Brand: Hama Pages: 4

Brand: Volvo Pages: 230

Interlock 700 Series

Brand: Scania Pages: 82

MagicSpeed MS900

Brand: Waeco Pages: 120

Brand: Saab Pages: 9

Brand: Reliant Pages: 116

Brand: Lund Pages: 12

Brand: Mitsubishi Pages: 57

Brand: Honda Pages: 330

Brand: Scion Pages: 58

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands