Chrysler pacifica hybrid 2017 Owner'S Manual Download Page 377

Page: 377 / 604

REFUELING THE VEHICLE

1. Press the fuel filler door release button (located in the

driver’s door).

2. The button press will initiate a sequence of events to

depressurize the fuel system. A message will display in
the cluster letting you know when the vehicle is ready to
be fueled.

NOTE:

•

After pushing the release button you will have 20
minutes to fuel the vehicle, beyond 20 minutes you
will need to press the release button again.

•

The fuel door could take up to 15 seconds to open. It
may take longer to open in some situations, such as
high ambient temperatures.

•

If you hear a hissing sound when the nozzle is inserted
into the filler pipe, wait to begin fueling the vehicle
until after the hissing sound stops.

Fuel Filler Door Release Switch

Instrument Cluster Message

STARTING AND OPERATING

375

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for pacifica hybrid 2017

Reviews:

Related manuals for pacifica hybrid 2017

Brands by name

Popular brands

Chrysler pacifica hybrid 2017, Owner'S Manual

Search results

Summary of Contents for pacifica hybrid 2017

Reviews:

Related manuals for pacifica hybrid 2017

Brands by name

Popular brands