manualshive.com logo in svg

Axis AXIS 570, User Manual

The user manual for the high-performance Axis AXIS 570 is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and information on operating and optimizing the features of this exceptional product. Get your copy now for an enhanced user experience!

Share
Download
background image

 

AXIS 5470e/570/670e

 

User’s Manual

Appendix A: SNA Parameter Overview

 

233

 

Mainframe Specific

Parameters

AS/400 Specific

Parameters

Parameter

Name

Default

Description

NODE_ID

Node ID

E07xxxxx, where 
"xxxxx" are the last 
five digits of the 
Print Server’s MAC 
address.

This is the SNA PU identification.

The first 3 digits is the IDBLK and the last five is 

the IDNUM.

When defining a VTAM Switched Major Node, 

this parameter should match the IDBLK and 
IDNUM values specified in the PU definition.
   Hexadecimal characters (0-9 and A-F) only are 
allowed.

Parameter

Name

Default

Emulation

Description

NWORK_NAME

Network 
Name

APPN

5494 only 

This is the Print Server Network Name.
 The value of this parameter is normally 
the same as the "Host Network Name", 
indicating that both the Print Server and 
the AS/400 system are located on the 
same APPN network. 
  The Network Name may comprise the 
letters A-Z and/or numerals 0-9, but 
must begin with a letter.
  The letters used should all be in 

UPPERCASE

 and a maximum of 8 

characters are allowed.

Summary of Contents for AXIS 570





























































































































































































































































































































Reviews:

No comments

Related manuals for AXIS 570

Canon Color imageCLASS MF8580Cdw Getting Started Manual preview
Color imageCLASS MF8580Cdw
Brand: Canon Pages: 36
Canon Color imageCLASS MF8280Cw Settings Manual preview
Color imageCLASS MF8280Cw
Brand: Canon Pages: 24
Canon Color imageCLASS LBP7660Cdn Quick Setup Manual preview
Color imageCLASS LBP7660Cdn
Brand: Canon Pages: 2
Canon Color imageCLASS 8180c Quick Start Manual preview
Color imageCLASS 8180c
Brand: Canon Pages: 24
Canon CD-300 Printer Manual preview
CD-300
Brand: Canon Pages: 30
Canon Color imageCLASS MF8080Cw Configuration Manual preview
Color imageCLASS MF8080Cw
Brand: Canon Pages: 46
Canon Color imageRUNNER LBP5360 Release Note preview
Color imageRUNNER LBP5360
Brand: Canon Pages: 3
Canon imageCLASS MF5550 Basic Manual preview
imageCLASS MF5550
Brand: Canon Pages: 136
Canon imageCLASS MF5850dn Settings Manual preview
imageCLASS MF5850dn
Brand: Canon Pages: 34
Canon imageCLASS MF5770 Setup Sheet preview
imageCLASS MF5770
Brand: Canon Pages: 2
Canon imagePRESS C7000VP Series Customer Expectation Document preview
imagePRESS C7000VP Series
Brand: Canon Pages: 48
Canon imageClass MF5650 Parts Catalog preview
imageClass MF5650
Brand: Canon Pages: 40
Canon imageCLASS MF4890dw Basic Operation Manual preview
imageCLASS MF4890dw
Brand: Canon Pages: 116
Canon imagePRESS C800 Series Operator'S Maintenance Manual preview
imagePRESS C800 Series
Brand: Canon Pages: 64
Canon imagePRESS C1+ Manual preview
imagePRESS C1+
Brand: Canon Pages: 36
Canon imageCLASS MP390 Setup Manual preview
imageCLASS MP390
Brand: Canon Pages: 2
Tally T6090 Maintenace Manual preview
T6090
Brand: Tally Pages: 202
Xerox Phaser 3010 User Manual preview
Phaser 3010
Brand: Xerox Pages: 76

Brands by name

Popular brands

Load more brands