Axis AXIS 570 User Manual Download

Page: 38 / 316

Section 3: Basic Installation

AXIS 5470e/570/670e User’s Manual

AXIS 670e

Token Ring

Print Servers

1. Start a DOS window.

2. Type the following commands:

Example

The host will return

Reply from 192.168.3.191 ...

or a

similar message. This indicates that the address has been set and that
communication is established.

Notes:

arp -s 802.5 <IP address> <Node address>

ping <IP address>

arp -d <IP address>

arp -s 802.5 192.168.3.191 00-02-31-48-00-61

ping 192.168.3.191

arp -d 192.168.3.191

•

The Node address is equal to the serial number, which can be found on the
underside label of the AXIS 670e.

•

When using the Windows 95 implementation of ARP, change the first line to:

arp -s <IP address> <Ethernet address>

where

<w95host IP

address>

is the IP address of your Windows 95 host.

•

When you execute the ping command for the first time, you will experience
a significantly longer response time than is usual.

•

By using the arp -d command, the static entry in the arp table is removed
from the host’s cache memory.

Summary of Contents for AXIS 570





























































































































































































































































































































Search results

Summary of Contents for AXIS 570

Reviews:

Related manuals for AXIS 570

Brands by name

Popular brands

Axis AXIS 570, User Manual

Search results

Summary of Contents for AXIS 570

Reviews:

Related manuals for AXIS 570

Brands by name

Popular brands